Mosmatic FL-CRY 520 Quick Start Manual Download Page 1

TD

 -

 80158

 D

/E

©

M

O

SM

AT

IC

 A

G

   

30

.09

.2

011

   

Ä

nd

er

un

ge

vo

rb

eh

al

te

Sub

je

ct t

ch

an

ge

 w

ith

ou

no

tic

e

FL-CRY 520

No. 80.158

1. 

Slide the upper fork (a) over the lower fork (b). Secure the two 

forks with the bolt (c) and the safety nut (d).

 

Note: the handle (e) and the ring (f) point in the same direction.

2. 

Connect the HP-gun (g) with the preinstalled adapter (h) to the 

quick connect (i).

3. 

Install the assembled fork (a+b) with the two bolts (k) and the 

two safety nuts (l) onto the fork holder (j). Works best if handle 

is in vertical position.

4. 

Connect the HP hose (m) with the quick connect (n) to the 

swivel (o).

 

Note: HP-gun (g) and nozzels are not included

 

For your own safety

Read all instructions before the initial operation. Check their 

proper condition and that they operate safely.

Always use protection gear when using products connected to 

high pressure.

Before any maintenance or nozzle-change, turn off the high 

pressure water supply, e.g.: turn off and secure the

 

power switch.

After turning off the system, allow all self propelled equipment 

to come to a complete stop before handling.

Safety regulations and guidelines (Accident Prevention Rules) 

from the manufacturer of your high pressure cleaner are 

applicable.

Nozzle installation according to nozzle manufacturer.

Do not move the unit over objects or uneven surfaces.

Do not lift up the unit while operating.

Do not run the unit if spray-arm is out of balance or bent, 

damage to the swivel will result.

No modifications to the unit are permitted.

The equipment may be installed and used only by particularly 

trained technical personnel.

1. 

Die obere Gabel (a) auf die untere Gabel (b) stecken, mit der 

Schraube (c) und der Sicherungsmutter (d) fixieren.

 

Hinweis

: Handgriff (e) und Ring (f) müssen in die gleiche

 

Richtung zeigen!

2. 

Die HD-Pistole (g) mittels der vormontierten Verschraubung (h) an 

die Quick-Verschraubung (i) anschliessen.

3. 

Die zusammengebaute Gabel (a+b) senkrecht in die Schlitze der 

Gabelhalter (j) einführen und mit den Schrauben (k) und den 

Sicherheitsmuttern (l) befestigen.

4. 

Den HD-Schlauch (m) mit der Verschraubung (n) am

 

Drehgelenk (o) anschliessen.

 

Hinweis: HD-Pistole (g) und Düsen sind nicht inbegriffen

 

Für Ihre Sicherheit

Alle Anleitungen sind vor erster Inbetriebnahme zu lesen.

 

Das Gerät ist auf ordnungsgemässen Zustand und Betriebssicherheit 

zu prüfen.

Alle Produkte die mit Hochdruck betrieben werden, dürfen nicht 

ungeschützt verwendet werden.

Bei Düsenwechsel sowie vor Wartungs- und Instandsetzungsarbeiten 

die Wasserzufuhr absperren, das System abschalten und gegen 

unbeabsichtigtes Einschalten sichern

Nach dem Abschalten des Systems läuft der Kreiselarm für kurze Zeit 

nach. Beim Anfassen des Kreiselarmes besteht

 Verletzungsgefahr.

Es gelten die Sicherheitsrichtlinien (Unfallverhütungsvorschriften) des 

Herstellers von Hochdruckgeräten.

Die Düsenbefestigung erfolgt laut Angaben des Düsen-Herstellers.

Das Gerät nicht über Gegenstände oder unebene Flächen führen.

Das Gerät während der Benutzung nicht anheben.

Bei einer Unwucht oder Krümmung des Kreiselarmes darf das Gerät 

nicht benutzt werden, da dadurch das Drehgelenk beschädigt wird.

An den Geräten dürfen keine Veränderungen vorgenommen werden.

Das Gerät darf nur von speziell ausgebildetem Fachpersonal 

installiert und bedient werden.

Flächenreiniger Commercial

Commercial Surface Cleaner

o

n

c

h

i

g

e

a

d

m

b

l

j

k

e

f

Attention:

High Pressure 500bar

do not use

unprotected!

Montageanleitung

Assembly instructions

( Diese Anleitung gilt für das Basismodel sowie für

 daraus entstehende Versionen)

( This instruction is valid for the base model as well as for 

 the resulting versions)

Achtung:

Hochdruck 500bar

nicht ungeschützt

verwenden!

Reviews: