background image

15

 4  MAINTENANCE

Moser  Baer  Photovoltaic  modules  require  very  little  maintenance,  following  is 
recommended to ensure optimum performance. 

1.

In view of the tilt angle of the PV modules , normal rainfall is sufficient to keep the 

module glass surface clean in most weather conditions. However, if dirt build up 
becomes  excessive,  clean  the  glass  surface  only  with  a  soft  cloth  or  sponge 
using water.

2.

A mild non abrasive cleaning agent can be used for stubborn dirt. Do not use high 
pressure water spray or chemicals to clean the module.

3.

In  order  to  ensure  proper  operation,  please  check  all  wiring  connections, 
condition of the insulation and mechanical connections every six months.

4.

Observe the maintenance instructions of all components used in the systems   
such as support frames, inverters, battery and  charge controller etc

(Typical Electrical Parameters)

Unit

AHFP

BAAP

BCAP

BDAP

BGFP

Nominal Power at STC, Pmax

[W]

75

100

120

130

170

Power tolerance at STC (min / max)

%

±3%

Voltage at Pmax, Vmp

[V]

17.2

22.93

17.4

28.5

36.5

Current at Pmax, Imp

[A]

4.51

4.51

7.12

4.64

4.7

Open circuit voltage, Voc

[V]

21.78

29.04

21.5

36.05

43.26

Short Circuit Current, Isc

[A]

4.8

4.8

7.6

5.05

5.1

NOCT

(±2)°C

47

47

47

47

47

Maximum System Voltage (IEC/UL)

V DC

1000/600

Temperature Coefficient of Pmax

%/K

-0.43

Temperature Coefficient of Voc

%/K

-0.344

Temperature Coefficient of Isc

%/K

0.11

IP Protection Level

IP 65

Absolute Maximum Rating

Operating Temperature

°C

-40 to +85

Mechanical Parameters

Cell Type

mm

Multi Crystalline Cells

Cell Size

Inch

5

5

6

5

5

No. of Cells (Matrix)

nos

36

48

36

60

72

Module Overall Dimensions (A)

mm

839

1095

1027

1353

1606

Module Overall Dimensions (B)

mm

810

813

999

813

806

Module Overall Dimensions (C)

mm

40

40

40

40

40

Weight ( Approx )

kg

7.5

10

11.5

13.3

15

2

Maximum Wind Load (Static load front & back {e.g. wind})

Pa

2400 (50 lbs/ft )

Resistance against Hail ( Hailstone Impact ) 

25 mm ice ball at 23 m/s at 11 impact location

Max series Fuse

Amp

7.5

7.5

10

7.5

7.5

2

Note: STC : Irradiance 1000 W/m  , cell Temperature at 25°C & AM 1.5 spectrum

- Module available in each category are within ± 10% power range.

- Refer product data sheet of particular category of module on Moser Baer web site for detailed information.

5 MODULE SPECIFICATIONS

Summary of Contents for Max CAAP





















Reviews: