Morris PROAG 16K PLUS, Operator'S Manual, Page: 46 / 190

Operation
5-8 October 2019 16K PLUS
Hooking Up for the First Time
Use the following outline as a checklist to ensure your
Auto Align Bale Runner is properly set up for use.
Step 1: Attach Bale Runner to Tractor
• Line up the Ball Hitch on the machine with the tractor
draw bar.
Parts Needed
1 Hitch Bolt ............................................................. 1 1/4” x 9” special
2 Hitch Washer ....................................................... 1 1/4” flat washer
1 Hitch Nut ............................................................. 1 1/4” plain
1 Hitch Jam Nut ...................................................... 1 1/4” special
1 Hitch Spacer Bolt ................................................ 5/8” x 8”
1 Hitch Spacer ........................................................ 3/4” ID x 3 9/16” tube
2 Hitch Plates ......................................................... 1/2” x 3” x 6 3/8”
1 Spacer Bolt Nut ................................................... 5/8” Nylock
1 Bolt Safety Pin ..................................................... 3/16” Snaplock Pin
Warning
Remember to turn off hydraulic system and
tractor and remove the key from ignition
before working on the Bale Runner.
• Secure the machine to the tractor with the 1 1/4” x
9” bolt threaded up through (1) - 1 1/4” flat washer,
tractor draw bar, lower hitch plate, ball, the upper
hitch plate, (1) - 1 1/4” flat washer, 1 1/4” nut, 1 1/4”
jam nut, and insert bolt safety pin through eyelet in
bolt.
Note: If tractor drawbar pin hole is larger than 1
1/4” a bushing must be added to provide a
snug fit. (Bushing not supplied)
• Secure the hitch plates into position with the (1) -5/8”
x 8” bolt threaded up through lower hitch plate, tractor
draw bar, (1) - 3/4” ID x 3 9/16” tubing, upper hitch
plate, and (1) - 5/8” lock nut.
• Adjust hitch clevis so
fender is level
front to back or
front of fender may be slightly lower than the back
not to exceed 1 1/2 inches.
WARNING: Do not allow anyone to
stand between the tractor and the
stacker while backing the tractor to
the machine hitch.
MATERIAL REQUIRED
NO.PCS.
Name2 Name1
SIZE Part No:
1 GRADE 8 HEX BOLT - 5/8 x 8 LG HEX BOLT - 5/8 x 8 LG GR8 10066A4 1
2 PLATE - DRAW BAR HITCH 1/2 H/R 44W 10142A2 2
1 1/4 x 1 3/4 Lg KLIK PIN W/CHAIN+COTTER 10247A4 3
1 * SPACER BUSHING 1-1/2 OD X .375W C1012 CDBW 10313A2 4
1 ASSY_STAGE8_16K 5
1 1-1/4 - 7 UNC - 2B HEX JAM NUT HEX JAM NUT - 1-1/4 C15768A4 6
1 5/8-11 UNC - 2B NYLON INSERT HEX LOCKNUT LOCKNUT - 5/8 NYLON INSERT C17295A4 7
1 HITCH BOLT HITCH BOLT K45448B2 8
1 1 1/4-7 UNC - 2B REGULAR HEX NUT HEX NUT - 1 1/4 P61D20 9
2 * TYPE A PLAIN WASHER WASHER - 1-9/32 ID X 2-1/2 OD X 10 GA S34182A4 10
1 TRACTOR-DRAW-BAR-PARTS 11
ASSY_STAGE10_16K
Description