Morgana DigiBook 450 Instruction Manual Download Page 67

Page: 67 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

11.3

ACCES TO ADVANCED SET UP PAGES

Area 1

Acces to advanced set up pages

Area 2

Buttons for language selection

Area 3

Buttons to adjust the display brightness and setting the date and time.

Area 4

Buttons to access technical area under password

Area 5

Buttons enabling and disabling tutorial

Button 6

Button to open windows of technical information

Button 7

With this button you can enable the rotation of the belt.

When this function is disabled, the machine does not ask anymore to verify the

pressure of the glue when a book has a thickness, compared to the previous, with a difference
greater than 10mm. When enabled the machine opens the window below as a reminder you have to
adjust the pressure of the glue.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands