Morgana DigiBook 450 Instruction Manual Download Page 55

Page: 55 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

11.1.2

LARMS

AGE

List of Warnings and Messages :

N°

Warnings

Description

A01

Machine Emergency

Verify that the emergency button is not pressed and press
green button.

A02

Fault Drive Arm

Driver error for cover feeder arm.

A03

Fault Drive Carriage

Driver error for carriage engine control.

A04

Fault Drive Delivery Arm

Driver error for delivery arm.

A05

Trip Safety Light Curtain

The SAFETY barriers are occupied with the machine in move-
ment.

A06

Inspection Door Open

Rear panel for loading/inspecting glue tank is open, close it
and press START.

A07

Encoder Error Side Jogger

Encoder error for cover guide of cover feeder. Verify there
are no obstructions for the movement, reset the alarm and
press START

A08

Encoder Error Suctions Bar

Encoder error of the cover feeder arm. Verify there are no
obstructions for the movement, reset the alarm and press
START

A09

Error Carriage Encoder

Encoder error of the carriage. Verify there are no obstruc-
tions for the movement, reset the alarm and press START

A10

Error Clamp Encoder

Encoder error for the clamp. Verify there are no obstruc-
tions for the movement, reset the alarm and press START

A11

Error Glue Nozzle Encoder

Encoder error for the nozzle. Verify there are no obstruc-
tions for the movement, reset the alarm and press START

A12

Error Press Encoder

Encoder error for the nipping station height adjustment.
Verify there are no obstructions for the movement, reset the
alarm and press START

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands