Morgana DigiBook 450 Instruction Manual Download Page 25

Page: 25 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

STORAGE

The information contained in this section must be observed in case of temporary storage of the ma-

chine that may occur in the following situations:



Installation of the machine not immediately after its delivery.



Uninstalling the machine.



Storage awaiting a new location.

The machine must be stored and transported under conditions of SAFETY as shown in the table be-

low.

Conditions of transportation and storage

Temperature average

23/+131°F

Humidity average

30/90%

Lighting

Adequate natural and / or artificial

Weather

Adequate weather protection

Space required

Adequate to allow the operations of lifting

and carrying in SAFETY.

Horizontal bolster

Horizontal bolster must have a capacity in

excess of the total mass of the machine.

In the case of removal or unused for long peri-

ods (over 30 days), it is necessary to drain the

glue system and to put inside the protection

cleaner.

The damage caused by this failure will

void the warranty of the glue device.

During periods of downtime you should not

open the tank containing the glue; otherwise it

accelerates the deterioration creating serious

permanent damage to the glue device.

The damage caused by this failure will

void the warranty of the glue device.

Protect with anti-corrosive products the parts sub-

ject to wear and work plans. Ref. to the section
“maintenance”.
Do not climb or place any objects on top of the

machine

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands