Morgan 21023 Assembly Instructions Manual Download Page 1

1. KEEP ALL HARDWARE PARTS OUT OF REACH OF CHILDREN.

2. DISPOSE PLASTIC PACKAGING MATERIAL IMMEDIATELY TO AVOID ANY RISK OF SUFFOCATION TO CHILDREN AND

ANIMALS.

Thank you for purchasing our product!

Please refer and use this assembly instruction to assemble the product.

 

Contact our customer service department in case there are any missing or 

damage parts or hardware. Replacement parts are normally shipped 

within 2 or 3 days.

We appreciate your business!

SAFETY PRECAUTION

Email: [email protected]

Within 30 days from delivery date

ASSEMBLY PREPARATION

1. Remove all packaging materials, staples and packing straps from the carton.

2. Refer to Parts List and Hardware List and ensure they are complete before you start assembling.

3. Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting

scratched.

TIPS FOR ASSEMBLY

1. Allow ample room for assembly and in close proximity to where product will be placed.

2. Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the furniture.

3. Please check all of the parts and quantities are included before assembly. Contact customer service for missing

parts.

4. Identify all of the parts, hardware and quantities required for each step.

5. During assembly, do not over-tighten any fittings as this may cause damage.

6. DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.

7. Always place the product on a flat surface.

8. Do not sit or stand on the partially assembled product; only use the product for which it is intended.

2

-Person

Assembly

45

 M

inutes

Assembly Time

(Approximate)

CARE AND MAINTENANCE

Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.

Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is

damaged or broken.

Never allow any kind of liquid to remain on your furniture. Absorption can cause wood to warp or delaminate.

Do not place hot items (e.g. hot drinks) directly onto the wood surface.

Do not drag and/or pull the furniture.

This product is for indoor and household use only - not for commercial use.

Tools Required

(Not Provided)

ASSEMBLY 

REQUIREMENTS: 

ASSEMBLY INSTRUCTIONS

Morgan Computer Desk with Hutch  Item

21023

Date : 

02

-

03

-

2016

Phillips 

Screwdriver

Flat 

Screwdriver

Page 1 of 1

6

 

Summary of Contents for 21023

















Reviews: