background image

4

© 2014 Monte Carlo Fan Company

11/1/2014

7

8

9

10

11

12

Install ball end of downrod into mounting 

bracket opening. Align (engage) slot on 

ball with tab on mounting bracket.

Warning:

 Failure to align slot on ball with 

tab may result in serious injury.

For Canadian installation and for USA fan 

and light kit combinations over 35 lbs, in 

both flush and downrod modes the safety 

cable must be installed into the house 

structure beams using 3” lag screws, 

washers and lock washers provided. 

Make sure that when the safety cable is 

fully extended the lead wires are longer 

than the cable and no stress is placed on 

the lead wires.

Note

: If Installing The Secondary Support 

Safety Cable in the U.S., Do Not Remove 
Knockouts In The Outlet Box.

  

Set dip switches on the Remote 

Transmitter and Remote Receiver to the 

same settings. This must be done so the 

units will communicate properly. If you 

have other fans you can set to control 

from one Transmitter by setting  

receivers the same as the Transmitter. If 

you have more than one fan with remote, 

you can set the dip switches to different 

positions to have separate control. 

Make wiring connections using wire 

connectors provided as indicated above.  

White from fan to White from remote 

marked N. Black from fan to Black from 

remote marked L. Blue from fan to Blue 

from remote marked FOR LIGHT. White 

from house to White from remote marked 

AC N. Black from house to Black from 

remote marked AC L. Connect all green 

grounded wires to Grounded wire from 

House. Make sure that no filaments are 

outside of the wire connectors.

Insert the remote receiver into mounting 

bracket. 

Partially loosen 2 of the set screws on 

mounting bracket corresponding to the 

slotted holes on the canopy upper ring. 

Remove the other 2 set screws. Save 

screws. Lift fan to mounting bracket, 

aligning the “L” shape holes with the 

screws on the mounting bracket. Turn the 

fan clockwise to lock in position. Install 

the other 2 canopy mounting set screws 

which were removed and tighten all 

screws securely.

Insert blade into the slot on flywheel.

Install blade with screws and fiber 

washers provided, aligning each of the 

holes as shown and tighten all screws 

securely. Repeat this process for 

remaining blades.

Note

: Make sure the side with a label 

“This side up” is installed upward.

SAFETY CABLE INSTALLATION

Dip switches

Lag screw

Safety cable

Washer

Lock washer

ON

Tab

Slot

Wall switch

White

White

Blue

Black

Black

Receiver

Ground/Green

Black

(Live)

White

(Neutral)

Power

source

This side up

Th

is

 s

id

up

Blade

Summary of Contents for 3BWR50XXD Series Fan










Reviews: