background image

 

Do not plug this device into the switched output of a preamplifier or other audio 
component. This amplifier requires higher current levels than these devices are 
designed to handle. 

 

Unplug this device from the power source when not in use. 

 

Never unplug the unit by pulling on the power cord. Always grasp the connector 
head or adapter body. 

 

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or 
detergents. For stubborn deposits, moisten the cloth with warm water. 

 

This device has no user serviceable parts. Do not attempt to open, service, or 
modify this device. 

 

INTRODUCTION 

Thank you for purchasing this Monolith 7-Channel 200-Watt Power Amplifier! 
This power amplifier features seven independent channels, each capable of delivering 
more than 200 watts of power into 8 ohm loads. A trigger input jack allows for remote 
power on/power off when a source device is powered on. Each channel features an 
optically coupled protection circuit, to prevent damage to the amplifier or speakers. 
 

FEATURES 

 

Seven independent 200-watt into 8 ohms amplifier modules 

 

20Hz ~ 20kHz ±0.1dB frequency response 

 

Gold plated RCA input and speaker output connectors 

 

Remote power-on trigger option 

 

Rated for 4 ~ 16 ohm loads 

 

Optically coupled short circuit protection 

 

 

Summary of Contents for MONOLITH 7















Reviews: