background image

SAFETY WARNINGS AND GUIDELINES

Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet.

This device is intended for indoor use only.

This device uses a grounded power cord and requires a ground connection for
safe operation. Ensure that the power source has a proper ground connection.
Do not modify the plug or use a "cheater" plug to bypass the ground connection.

Ensure that the power outlet used to connect this device does not exceed the
rated maximum voltage, listed on the back panel of the device.

Ensure that power is turned off and disconnected before making any electrical
connections.

Disconnect from the power source during lightning storms or when not in use.

Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords.

When disconnecting the power cord do not pull on the cord itself. Instead, grasp
the plug connector head to disconnect it from the power socket.

The power cord uses the US standard color coding with green for ground.

This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.

Do not use chemical cleaners or solvents to clean the cabinet. Use only a soft
dry cloth. For stubborn dirt, moisten the cloth with warm water.

This device ventilates excessive heat through the slots and openings in the case.
Do not block or cover these openings. Ensure that the device is in an open area
where it can get sufficient airflow to keep from overheating.

Ensure that there are no flammable materials within 0.5m (20 inches) of the light.

Do not connect this light to a dimmer.

This device has a pass-through AC outlet, which allows you to cascade multiple
lights through a single power source connection. When using 110 VAC level
power, do not cascade more than 40 lights. If using 220 VAC level power, do not
cascade more than 30 lights.

Summary of Contents for 612610











Reviews: