Monmouth Scientific Cleanroom Kit 4M Installation Manual Download Page 56

Page: 56 / 72

Issue 03 – June 2018

Calibration of the low-airflow alarm

When the normal running fan speed has been set, note the position on the speed control
knob.

Reduce the speed to the required alarm level

Press and hold the Alarm Mute button for 10 seconds until single ‘beep’ is heard. Release
the button. 3 ‘beeps’ will sound indicating the alarm point has been stored.

Reset the fan speed to the original level.

Check operation of the low airflow alarm by reducing the speed to the alarm level. The alarm
should sound and the warning light should come on.

Reset the fan speed to the original set point and repeat the procedure with all other
modules if fitted.

Maintenance

Changing the pre-filters

If the airflow monitoring system indicates a low airflow this normally indicates that the Pre-Filter/s
require changing

Turn the system off

Remove the thumb screws securing each of the pre-filter retaining frames.

10.

Withdraw the filters and fit a replacements

11.

Replace the retaining frame and re start the system

Replacement filter part numbers

Replacement filters are available from Monmouth Scientific:

Pre-Filters Part No:

PF-0033

2 off per unit

HEPA filter Part No:

HF-0043

1 off per unit

Summary of Contents for Cleanroom Kit 4M









































































Search results

Summary of Contents for Cleanroom Kit 4M

Reviews:

Related manuals for Cleanroom Kit 4M

Brands by name

Popular brands

Monmouth Scientific Cleanroom Kit 4M, Installation Manual

Search results

Summary of Contents for Cleanroom Kit 4M

Reviews:

Related manuals for Cleanroom Kit 4M

Brands by name

Popular brands