CR1031E Hand Crimp Tool for “Disk Drive” Terminals
Doc No. 11-01-0206
Release Date: 06-07-93
UNCONTROLLED
COPY
Page 2 of 5
Revision: G
Revision Date: 03-17-05
CONDITIONS:
After crimping, the conductor profiles should measure the following (see notes on page 4).
Terminal
Series No.
Wire Size
Cond. Crimp
Height (Ref)
Punch Width (Ref)
Pull Force Min. Profile
Cond.
AWG mm
2
mm
In.
mm
In.
N
Lb.
A
B
8980-3L
14
2.00
1.47-1.52 .058-.060
2.32
.091
266.9
60.00
X
8980-3L
16
1.30
1.37-1.42 .054-.056
2.32
.091
133.4
30.00
X
8980-3L
18
0.80
1.30-1.35 .051-.053
2.32
.091
89.0
20.00
X
8980-3L
20
0.50
1.22-1.27 .048-.050
2.32
.091
71.2
16.00
X
8980-6L
14
2.00
1.47-1.52 .058-.060
2.32
.091
266.9
60.00
X
8980-6L
16
1.30
1.37-1.42 .054-.056
2.32
.091
133.4
30.00
X
8980-6L
18
0.80
1.30-1.35 .051-.053
2.32
.091
89.0
20.00
X
8980-6L
20
0.50
1.22-1.27 .048-.050
2.32
.091
71.2
16.00
X
8980-6L1
18
0.80
1.19-1.27 .047-.050
1.92
.076
89.0
20.00
X
8980-6L1
20
0.50
1.04-1.12 .041-.044
1.92
.076
71.2
16.00
X
8980-6L1
22
0.35
0.94-1.02 .037-.040
1.92
.076
44.5
10.00
X
8980-6L-LF
14
2.00
1.47-1.52 .058-.060
2.32
.091
266.9
60.00
X
8980-6L-LF
16
1.30
1.37-1.42 .054-.056
2.32
.091
133.4
30.00
X
8980-6L-LF
18
0.80
1.30-1.35 .051-.053
2.32
.091
89.0
20.00
X
8980-6L-LF
20
0.50
1.22-1.27 .048-.050
2.32
.091
71.2
16.00
X
8980-6L1-LF
18
0.80
1.19-1.27 .047-.050
1.92
.076
89.0
20.00
X
8980-6L1-LF
20
0.50
1.04-1.12 .041-.044
1.92
.076
71.2
16.00
X
8980-6L1-LF
22
0.35
0.94-1.02 .037-.040
1.92
.076
44.5
10.00
X
OPERATION
Open the tool by squeezing the handles together, at the end
of the closing stroke, the ratchet mechanism will release the
handles, and the hand tool will spring open.
Crimping Terminals
1. Lift the locator blade and place the terminal into the
correct die profile (A or B), release the locator blade.
Not all tools are equipped with a locator or locator blade.
2. Partially close the tool until the terminal is held in place,
(See Figure 2).
3. Place a wire into the terminal and up against the locator blade, (See Figure 3). On tools
without locators line the wire up with the conductor and insulation grips visually.
TERMINAL
PRE-STRIPPED
WIRE
Figure 1
