manualshive.com logo in svg

Moeller DeviceNet NZM-XDMI612, User Manual, Page: 12 / 50

Share
Download
Moeller DeviceNet NZM-XDMI612 User Manual Download Page 12

CANopen Interface

8

05/04 AWB1230-1543GB

Commissioning the 
CANopen interface

Detailed information on the installation and assembly of the 
EASY221-CO can be found 

a

 AWB2528-1479GB.

The following steps must be completed in order to 
commission the EASY221-CO interface:

X

Use the EASY-Link connection plug to connect the 
EASY221-CO to the DMI (basic unit).
To plug the connector into the DMI, push up the cover flap 
on the right side of the housing.

X

Connect up the 24 V DC power supply for the EASY221-
CO interface (

Do not switch on yet!

).

X

Connect up the CANopen connector to the EASY221-CO.
The pin assignments can be found 

a

 AWB2528-

1479GB.

X

Check that all connections are correct.

X

Switch on the power supply for the DMI and the CANopen 
interface.

X

Set the required bus node address via the display and the 
keypad on the DMI.
The procedure can be found 

a

 AWB1230-1441GB.

X

Configure the CANopen system, with the EASY221-CO as 
a new node.
(Follow the procedure described in AWB2528-1479GB.)

X

Start the CANopen system.

After these steps, the CANopen should be in the “Pre-
operational” status (RUN-LED flashes) or ”Operational” 
(RUN-LED lights up continuously).

h

Further explanation of the displays and operating states 
can be found 

a

 AWB2528-1479GB, Chapter 4.

Summary of Contents for DeviceNet NZM-XDMI612



















































Reviews:

No comments