background image

EE

I

–3040 Office Chair

Customer Service 908-368-1025︱www.modwayfurniture.com

Page 1 of 6

Thank you for purchasing the

MODWAY OFFICE CHAIR.

Before you start, here is some helpful advice:
1

.

We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step

instructions.

2

.

Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or

padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.

3

.

Please do not use any tools other than those provided or recommended in these instructions.

4

.

Please do not throw away any of the packaging or the instruction until you have checked all the components

and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.

5

.

Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the

components from time to time, so please save the tools that have been provided.

6

.

Please keep all fitting out of reach of children.

Hardware:

A.

Bolt M6x20mm

x 4

B.

Bolt M6x40mm

x 4

C.

Flat Washer M6

x 4

D.
E.

Allen Wrench

x1

Component:

1 Base x1

2 Cylinder Column x1

3 Control Mechanism x1

4 Seat x1

5 Back Frame x1

6 Castor x5

7 Foot Ring x1

                              1

                              6

                              7

                              3

                              4

                              5

                              6

                              6

                              6

                              6

Summary of Contents for EEI –3040







Reviews: