The HiRes Video Company
EN
HiRes Video Innovations
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost-efficient.
Security Door Opener: Quick Install
Security Door Opener with
Access Code Storage
Controls door openers via encrypted MxBus
communication and provides a doorbell for indoor
installation (includes backup power supply for
bell features and door opener)
Standard Connection:
Security Door Opener with
Door Station, Door Opener and Door Sensors
Installing the Security Door Opener
Installing the module follows the procedure described in the
T24 System Manual Part 1, in Section 2.5, “Installing
the Security Door Opener”. Please also refer to this section to get more information on connection variants (e.g.
relay or Mediator operation).
Charging the Battery Pack after Installing
Once have installed the module, you need to charge the Security Door Opener's battery pack without interruption
for at least 12 hours. The IP Video Door Station T24 and its PoE power supply automatically charge the module via
the MxBus two-wire connection. Note that you should not use the door opener during this time (except for a short
functional test). This ensures that you can extend the life cycle of the high-quality NiMH battery pack (heavy-duty
industrial grade) to several years (given normal usage).
Supported Door Opener Variants
Standard door openers with 6 to 12 V AC (min. 16 Ω internal resistance) can be attached directly to the Security Door Opener;
such a door opener is powered by the integrated battery pack. In this case, you do not need an additional power
supply for the door opener. As an alternative, you can also connect door openers with up to 24 V AC/DC (max. 1 A)
using an external power supply (relay operation) or a self-locking door lock (“Mediator”; see
T24 System Manual
Part 1, Section 2.5, “Installing the Security Door Opener”).
Replacing the Battery Pack
First, dismount the Security Door Opener (see
T24 System Manual Part 1, Section 2.4.6, “Removing and Exchanging
Modules”). Next, replace the battery pack and install the Security Door Opener again (see Section 2.5.4, “Installation
Using Cavity or In-Wall Socket”).
Replacing the Security Door Opener
If the Security Door Opener needs to be replaced against all expectations, you need a current backup of the system
configuration. This will ensure that you can restore the encryption data later on. Please follow the steps outlined
in the
T24 System Manual Part 2 in Section 5.2, “Backup & Restore”. To dismount the Security Door Opener, follow
the steps in the
T24 System Manual Part 1 in Section 2.4.6, “Removing and Exchanging Modules”.
• Open door, doorbell off/on, change sound
• Door indicator (open, closed, locked)
• Status LEDs for signaling
• Backup power supply with rechargeable battery
• Connection for door opener, door sensor and door lock
sensor
MOBOTIX Security Door Opener
MX-Door1-INT
includes 2 additional frames
(concave, angular), cavity wall socket
and mounting supply
Outdoor
Indoor
Door
2
6
MxBus (YSTY 0.8 mm – max. length: 50 m)
Theft protection (YSTY 0.8 mm – max. length: 50 m)
Door opener, door sensor, lock sensor
(YSTY 0.8 mm – max. length: 50 m)
Security Door Opener
MX-Door1-INT
Door station
2
For additional information on the other connection variants and for installing,
see the
T24 System Manual Part 1
on www.mobotix.com > Supprt > Manuals.
Connector for battery pack
MX-Door1-BAT
OUT –
OUT 1+
Theft protection /
Door opener
Theft protection
IN –
OUT 2+
Door sensor /
Door lock sensor
Door opener
IN 2+
BUS +
Door lock sensor
MxBus +
IN 1+
BUS –
Door switch
MxBus –
