background image

© MOBATIME 

 

5 / 20 

800640.03 

 
 
 

1.5 Building Department / Authority Permit 

If necessary a building department / authority permit should be requested before mounting. 
 

1.6 Manner of fastening (WA or DA):  

 
For wall, ceiling or pedestal fastening (W, D or S) set bolts or screws as described in chapter 1.1, for wall 
bracket (WA) resp. ceiling suspension (DA) set bolts or screws as described in chapter 1.2 (recommended bolt 
Ø 12 mm). 
For pole mounting, prepare central pole taking in account wind load stressing. Feed electrical line from inside 
pole as wall bracket (WA and SM), ceiling suspension (DA) or central pole (ZM) and then fix the clock. 

Warning: Before mounting, all wire must be disconnected from mains! 

1.7 Opening clock 

 

Disconnect mains 230V/50Hz BEFORE start working at clock inside! 
For opening clock, unscrew the two screws of the profiles on the side of the clock. Remove the profile without 
jam, it is protected against fall out by a chain. 
Pull out dial (with movement) lateral out of the profiles. The illumination is suspend with rubber band and can 
easily be moved beside. 

 

 

Self setting movements: Do not touch hands! 

 

1.8 Closing clock 

Introduce dial lateral in the profile, close profile and fix the clock with the two fixing screw. 
 

Pay attention that cables do not cause shadowing on illuminated dial. 

1.9 Cleaning 

 

 

 

Clean glass with a humid cloth. Do not use solvent, evaporating or organic detergent. 
 
 

2 Electrical 

connections 

2.1 Mains power supply 

The mains power supply for illumination and clock movement may only be connected from a licensed 
electrician. 
Use the same phase with only one fuse for illumination and movement. 
The timing switch for the illumination has to be installed with respect to the constructional situation. The power 
supply for the movements has to be permanent.  

Warning:  

Disconnect mains 230V/50Hz BEFORE start working at clock inside! 
 
For cable entry of the line for minute impulse resp. the DCF-77 – radio receiver a second membrane rubber 
bushing is prepared. 
Connections and plug-in connections see mounting plates (pages 9-15). 
 

 

 

 

 

 

Summary of Contents for PROFILINE Series





















Reviews: