Mizuho MOS-1302B Operator'S Manual Download Page 32

Page: 32 / 86

Operation

Lock and unlock the operating table

LOCK

1. Press

and

simultaneously.

The brake will actuate and the operating table
will be locked. The operating table will not move
up until the brake has fully actuated.

Lock operating table

1. Press

and

simultaneously for one

second or more.
The brake will be unlocked to allow the operating
table to be moved to another place.

Unlock operating table

NOTE

The operating table can be
locked or unlocked once

and

are pressed.

It takes about 7 to 8 seconds

for the operating table to be

locked or for the brake to be

unlocked.

WARNING

- Make sure the table is locked

after the brake is applied.

- If it is necessary to stop

moving, press the emergency

stop switch.

- Do not unlock the brake

with the patient on the table.

Otherwise the patient may

tumble off the table.

SEAT DOWN

SEAT UP

SEAT DOWN

SEAT UP

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands