Mitsubishi QCPU Structured Programming Manual Download Page 102

Page: 102 / 242

5-64

5.2 Serial Communication and Modem Interface Instruction
5.2.8 BUFRCVS instruction

Z_BUFRCVS

5.2.8

BUFRCVS instruction

Z_BUFRCVS

*1: Local devices and file registers per program cannot be used as setting data.

Function

This instruction receives data with an interrupt program during communication using the
nonprocedural protocol or bidirectional protocol.

Z_BUFRCVS

indicates the following instruction.

Z_BUFRCVS

Input argument

EN:

Executing condition

:Bit

Un*:

Start I/O number of the module
(00 to FE: Higher two digits when expressing the I/O
number in three digits)

:String

Reception channel number
1: Channel 1 (CH1 side)
2: Channel 2 (CH2 side)

:ANY16

Output argument

ENO:

Execution result

:Bit

Start number of the device that stores read data
* Receive data are read from the receive area of buffer

memory.

:ANY16

Setting

data

Internal device

R, ZR

Constant

K, H

Others

Bit

Word

Bit

Word

−

Structured ladder

Z_BUFRCVS

ENO

Z_BUFRCVS

(EN, U

*, s, d);

ENO:=

Summary of Contents for QCPU



















































































































































































































































Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands

Mitsubishi QCPU, Structured Programming Manual

Search results

Summary of Contents for QCPU

Reviews:

Related manuals for QCPU

Brands by name

Popular brands