Mitsubishi NZ2GF2B-60DA4 User Manual Download Page 136 | Manualshive

Page: 136 / 174

background image

134

(4) Remote READY (RXB)

This signal is used as an interlock condition when the master station reads/writes data to/from the remote register
or remote buffer memory areas of the D/A converter module.
The signal turns on when the module power supply is turned on.
When Error flag (RXA) turns on, the signal turns off.

(5) Alert output signal (RX1E)

If the digital value in any D/A conversion enabled channels becomes any of the following status, this signal is
turned on.

• Digital value > Alert output upper limit value
• Digital value < Alert output lower limit value

(a) How to turn off the signal

Turn off the signal by either of the following methods.

• Turning on and off Alert output clear request flag (RY1E)
• Turning on and off Initial data setting request flag (RY9)

When an alarm code is stored in Latest warning code (RWr1), this signal is cleared.

(6) External power supply monitor state flag (RX1F)

This signal turns on when the external power supply monitoring function is being activated by External power
supply monitor request flag (RY1F).

For the external power supply monitoring function, refer to the following.

• External power supply monitoring function (

Page 98, Section 8.11 (2))

Alert output signal
(RX1E)

Latest warning code
(RWr1)

Alert output clear
request flag (RY1E)

Controlled by the D/A converter module

Controlled by the program

ON

ON

OFF

OFF

0

0

Alert

External power supply monitor
function

External power supply monitor
request flag (RY1F)

Changed by

the user

OFF

OFF

ON

ON

OFF

OFF

Controlled by the D/A converter module

Changed by

the user

External power supply monitor
status flag (RX1F)

Disabled Enabled

Disabled

«
...
134
135
136
137
138
...
»

Summary of Contents for NZ2GF2B-60DA4















































































































































































Reviews:

No comments

Related manuals for NZ2GF2B-60DA4

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: HANYOUNG NUX Pages: 56

Brand: LAS Pages: 6

Brand: U-Prox Pages: 3

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: Daikin Pages: 46

Brand: Daikin Pages: 26

GRASS VALLEY MDX-3901

Brand: Belden Pages: 45

Brand: Desoutter Pages: 74

Brand: jablotron Pages: 2

Brand: Nautronic Pages: 6

Brand: Redbusbar Pages: 12

Brand: Nibe Pages: 20

Brand: Mircom Pages: 20

Brand: Swagelok Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands