Mitsubishi MELSEC iQ-R series User Manual Download Page 60

Page: 60 / 86

7 OPERATION EXAMPLES
7.2 Program Examples

Standard control (When using the inter-module simultaneous
temperature rise function)

System configuration

The following shows a system configuration example.

Parameter settings

Connect an engineering tool to the CPU module and set parameters.

In these program examples, use the default setting for the parameters other than the set parameters. For
parameters, refer to the following.



MELSEC iQ-R Temperature Control Module User's Manual (Application)

■

Setting modules

For how to set the module, refer to the following.



Page 52 Setting modules

(1) Power supply module (R61P)
(2) CPU module (R120CPU)
(3) Temperature control module 1 (R60TCTRT2TT2)
(4) Temperature control module 2 (R60TCTRT2TT2)
(5) Input module (RX10)

(1)

(2)

(3)

(4)

(5)

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands