Mitsubishi MELSEC iQ-R series User Manual Download Page 43

Page: 43 / 86

6 INSTALLATION AND WIRING

6.3 External Wiring

R60TCTRT2TT2BW

Standard control

*1 Use the shielded compensation lead wire.
*2 Use the shielded cable.

• To use the heater disconnection detection function, the CT input channel assignment must be set. Since the

CT1 is used in the loop of CH1 in the above wiring example, set "CH1" for "CT input channel assignment
setting" in the "CT setting" of CT1.

• Use the compensation lead wire for the cable of a thermocouple. The shielded cable cannot be used. If the

compensation lead wire is not used, and when the cold junction temperature compensation resistor (1) is
away from the end tip (2) of a thermocouple, the (ambient) temperature (3) difference may lead to a faulty
temperature process value (PV).

COM-

CH1+
CH1-

CH2+
CH2-

CH4+
CH4-

CT1
CT1

CT2
CT2

CT8
CT8

R60TCTRT2TT2BW

(CT)

24VDC

Current sensor

CT input circuit

Controlled
object

Internal
circuit

Filter

Connector
Connector

R60TCTRT2TT2(BW)

(1)

(3)

(2)

Summary of Contents for MELSEC iQ-R series























































































Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands

Mitsubishi MELSEC iQ-R series, User Manual

Search results

Summary of Contents for MELSEC iQ-R series

Reviews:

Related manuals for MELSEC iQ-R series

Brands by name

Popular brands