background image

EN-10

Setting up your projector

Setting up the screen

Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the 
projection angle of the projector. (See page 11.)
•  Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of 

the screen center. 

•  Do not install the screen where it is exposed to direct sunlight or lighting. Light directly refl ecting on the screen 

makes the projected images whitish and hard to view. 

Screen size and projection distance 

Refer to the following table to determine the screen size and projection distance.

W1

H1

H2

H

L

W1

W

L

W1

H1

H2

H

L

W1

W

L

•  You are recommended to install the projector as close to the screen as possible within the specified projection 

distance range for your screen size.

•  Depending on the installation conditions, warm air that is emitted from the exhaust vents may fl ow into the intake 

vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images. 

When the aspect ratio of the screen is 16:9

Screen size

Projection distance (L)

Lens movable range

Diagonal size

Height (H)

Width (W) 

Shortest (Wide) Longest (Tele)

H1

H2

W1

inch

cm

inch

cm

inch

cm

inch

m

inch

m

inch

cm

inch

cm

inch

cm

60

152

29

75

52

133

104

2.6

133

3.4

15

38

4

10

3

7

80

203

39

100

70

177

140

3.5

178

4.5

20

51

5

13

4

9

100

254

49

125

87

221

175

4.5

223

5.7

25

63

7

17

4

11

150

381

74

187

131

332

264

6.7

336

8.5

37

94

10

25

7

17

200

508

98

249

174

443

354

9.0

449

11.4

49

125

13

34

9

22

250

635

123

311

218

553

443

11.2

-

-

62

156

17

42

11

28

The above fi gures are approximate and may be slightly different from the actual measurements.

When the aspect ratio of the screen is 4:3

When the aspect ratio of the screen is 4:3, the positional relation 
between the projected image and the screen is as shown on the right. 
Refer to the following table for installation.

When the aspect ratio of the image is 16:9

Screen size (4:3)

Size of the projected image (16:9)

Black 

space (B)

Projection distance (L)

Lens movable range

Diagonal size

Height (SH)

Width (W) 

Height (H)

Width (W) 

Shortest (Wide) Longest (Tele)

H1

H2

W1

inch

cm

inch

cm

inch

cm

inch

cm

inch

cm

inch

cm

inch

m

inch

m

inch

cm

inch

cm

inch

cm

60

152

36

91

48

122

27

69

48

122

5

11

95

2.4

121

3.1

14

35

4

9

2

6

80

203

48

122

64

163

36

91

64

163

6

15

128

3.2

163

4.1

18

46

5

12

3

8

100

254

60

152

80

203

45

114

80

203

8

19

161

4.1

204

5.2

23

58

6

15

4

10

150

381

90

229

120

305

68

171

120

305

11

29

243

6.2

308

7.8

34

86

9

23

6

15

200

508

120

305

160

406

90

229

160

406

15

38

324

8.2

412

10.5

45

115

12

31

8

20

250

635

150

381

200

508

113

286

200

508

19

48

406

10.3

-

-

57

144

15

39

10

26

The above fi gures are approximate and may be slightly different from the actual measurements.

BB

H

SH

W

Front projection

Front projection, ceiling mounting

Summary of Contents for HD8000


















































Reviews: