Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 77 | Manualshive

Page: 77 / 538

background image

To unfasten

CAUTION

l

As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could
damage the vehicle.

1. Hold the latch plate (A) and push the

button on the buckle (D).

2. To release the buckle (C), press the but-

ton (F) with the latch plate (A).

3. Retract the seat belt and remove it from

the seat belt guide (E).

4. After the seat belt is retracted complete-

ly, insert the small latch plate (B) into
the upper slit (G) and the latch plate (A)
into the lower slit (H).

Rear seat belt storage

E00405301606

When the seat belt is not in use, store it as
shown in the illustration.

Seat belts

4-13

OGKE18E1

Seats and seat belts

4

«
...
75
76
77
78
79
...
»

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Cherokee 16 1982

Brand: Jeep Pages: 1311

Brand: SnapPad Pages: 5

Brand: EEZ RV Pages: 31

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: Mercedes-Benz Pages: 54

Brand: Hank Pages: 2

Brand: Mopar Pages: 17

Brand: MacNeil Pages: 2

Brand: Istar Pages: 6

Brand: Conrad Pages: 8

Brand: Porsche Pages: 1005

Brand: ZeroRPM Pages: 41

Brand: Alu-Cab Pages: 6

Brand: Jeep Pages: 116

Brand: Nedap Pages: 18

Brand: SSANGYONG Pages: 214

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands