background image

© 2015 Mitsubishi Electric US, Inc. 

5

Example 4: Single-stage Cooling with Alternate Primary Heating Source

Note: For this configuration, it is recommended to set SW2-6 to the 

 

OFF position.

Follow the wiring from example 2, with the following adjustments:
1. Connect thermostat W1 to the alternate heat source.
2. Connect the thermostat W2 terminal to the PAC-US444CN-1 W1 terminal.

Connector

Purpose

Purpose

TC

Common (In)

C

C

Common (Out)

C

TR

24VAC (In)

R

R

24VAC (Out)

R

G3

Fan High

High Fan Speed 

G2

Fan Medium

Medium Fan Speed 

G1

Fan Low

Low Fan Speed

Y2

Y2

Stage 2 Cooling

Y1

Y1

Stage 1 Cooling

W2

W2

Stage 2 Heating

W1

W1

Stage 1 Heating

G

G

Fan

4. How to Install

 1.  Choose a place where to install the PAC-US444CN-1. The device provides two 

mounting holes that can be used to mechanically affix the case to a solid surface. 

Double-sided tape may be used to affix the device. When using tape, ensure that 

the tape is approved for use within the anticipated operating temperature ranges.

 2.  Install  the  transformer,  as  necessary,  per  building  code  and  manufacturer’s 

installation instructions.

 3.  Connect the PAC-US444CN-1 cable to the connector CN105 on the indoor unit 

control board.

 4.  Connect PAC-US444CN-1 terminals using 18 AWG wire.

Device Configuration

Initial settings can be configured via the two banks of dip switches on the circuit 

board, SW1 and SW2. The circuit board can be accessed by unfastening the four 

screws on the back of the case.

sandium.com

Summary of Contents for PAC-US444CN-1









Reviews: