background image

JG79J821H01

 ENGLISH

Required Tools for Installation

Phillips screwdriver

Level

Scale

Utility knife or scissors

3 in. (75 mm) hole saw

Torque wrench

Wrench (or spanner)

5/32 in. (4 mm) hexagonal 

wrench

Flare tool for R410A

Gauge manifold for R410A

Vacuum pump for R410A

Charge hose for R410A

Pipe cutter with reamer

MSZ-GS30/36NA

MSY-GS30/36NA

1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY

•  Be sure to read these safety precautions and instructions.

‡ %HVXUHWRREVHUYHWKHZDUQLQJVDQGFDXWLRQVVSHFL¿HGKHUH

•  After reading this manual, be sure to store it with the OPERATING INSTRUCTIONS for future reference.

•  Please report to your supply authority or obtain their consent before connecting this equipment to the power supply system.

  Do not install the unit by yourself (user).

 ,PSURSHURULQFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHHOHFWULFVKRFNLQMXU\GXHWR

WKHXQLWIDOOLQJRUZDWHUOHDNDJH&RQVXOWDTXDOL¿HGLQVWDOOHURUWKHGHDOHUIURP

whom you purchased the unit.

  Follow the instructions detailed in the installation manual.

 ,QFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHRUHOHFWULFVKRFNLQMXU\GXHWRWKHXQLW

falling, or leakage of water. 

 When installing the unit, use appropriate protective equipment and tools for 

safety.

  Failure to do so could cause injury.

  Install the unit securely in a place that can bear the weight of the unit.

  If the installation location cannot bear the weight of the unit, the unit could fall 

causing injury.

  Do not alter the unit.

 ,WPD\FDXVH¿UHHOHFWULFVKRFNLQMXU\RUZDWHUOHDNDJH

■ 

Perform electrical work according to the installation manual and be sure to use 

an exclusive circuit. Do not connect other electrical appliances to the circuit.

 ,IWKHFDSDFLW\RIWKHSRZHUFLUFXLWLVLQVXI¿FLHQWRUWKHUHLVLQFRPSOHWHHOHFWULFDO

ZRUNLWFRXOGUHVXOWLQD¿UHRUDQHOHFWULFVKRFN

  Ground the unit correctly.

  Do not connect the ground wire to a gas pipe, water pipe, lightning rod or tele-

phone ground. Defective grounding could cause electric shock.

■ 

Do not damage the wires.

 'DPDJHGZLUHVFRXOGFDXVH¿UH

■ 

Be sure to shut off the main power when setting up the indoor P.C. board or 

wiring.

  Failure to do so could cause electric shock.

 8VHWKHVSHFL¿HGZLUHVWRVHFXUHO\FRQQHFWWKHLQGRRUDQGRXWGRRUXQLWV$WWDFK

WKHZLUHV¿UPO\WRDYRLGDSSO\LQJVWUHVVWRWKHWHUPLQDOEORFN

 ,PSURSHUFRQQHFWLRQFRXOGFDXVH¿UH

■ 

'RQRWLQVWDOOWKHXQLWLQDSODFHZKHUHÀDPPDEOHJDVPD\OHDN

  If gas leaks and accumulates around the unit, it could cause an explosion.

  Do not use intermediate connection of the power cord or the extension cord.

Do not connect many devices to one AC outlet.

 ,WFRXOGFDXVHD¿UHRUDQHOHFWULFVKRFN

■ 

8VHWKHSDUWVSURYLGHGRUVSHFL¿HGSDUWVIRUWKHLQVWDOODWLRQZRUN

 7KHXVHRIGHIHFWLYHSDUWVFRXOGFDXVHDQLQMXU\RUOHDNDJHRIZDWHUGXHWRD¿UH

an electric shock, the unit falling, etc.

■ 

When plugging the power supply plug into the outlet, make sure that there is 

no dust, blockage, or loose parts both in the outlet and on the plug. Verify that 

the power supply plug is completely in the outlet. 

  If there is dust, blockage, or loose parts on the power supply plug or the outlet, it could 

FDXVHHOHFWULFVKRFNRU¿UH,IORRVHSDUWVDUHIRXQGRQWKHSRZHUVXSSO\SOXJUHSODFHLW

■ 

Securely attach the electrical cover to the indoor unit and the service panel to 

the outdoor unit.

  If the electrical cover of the indoor unit and/or the service panel of the outdoor unit are 

QRWDWWDFKHGVHFXUHO\GXVWZDWHUHWFFRXOGFROOHFWLQWKHXQLWDQGFRXOGFDXVHD¿UHRU

an electric shock.

■ 

When installing, relocating, or servicing the unit, make sure that no substance 

RWKHUWKDQWKHVSHFL¿HGUHIULJHUDQW5$HQWHUVWKHUHIULJHUDQWFLUFXLW

  Any presence of foreign substance such as air can cause abnormal pressure rise and 

PD\UHVXOWLQH[SORVLRQRULQMXU\7KHXVHRIDQ\UHIULJHUDQWRWKHUWKDQWKDWVSHFL¿HG

for the system will cause mechanical failure, system malfunction, or unit breakdown. 

In the worst case, this could lead to a serious impediment to securing product safety.

■ 

Do not discharge the refrigerant into the atmosphere. Check that the refrigerant gas 

does not leak after installation has been completed. If refrigerant leaks during 

installation, ventilate the room.

 ,IUHIULJHUDQWFRPHVLQFRQWDFWZLWKD¿UHKDUPIXOJDVFRXOGEHJHQHUDWHG

 ,IUHIULJHUDQWJDVOHDNVLQGRRUVDQGFRPHVLQWRFRQWDFWZLWKWKHÀDPHRIDIDQ

heater, space heater, stove, etc., harmful gases will be generated.

■ 

Use appropriate tools and piping materials for installation. 

  The pressure of R410A is 1.6 times higher than R22. Not using the appropriate 

tools and materials, or improper installation could cause the pipes to burst causing 

an injury. 

■ 

When pumping down the refrigerant, stop the compressor before disconnecting 

the refrigerant pipes.

  If the refrigerant pipes are disconnected while the compressor is running and the 

stop valve is open, air could be drawn in and the pressure in the refrigeration cycle 

could become abnormally high, causing the pipes to burst. 

■ 

When installing the unit, securely connect the refrigerant pipes before starting 

the compressor.

  If the compressor is started before the refrigerant pipes are connected and the 

stop valve is open, air could be drawn in and the pressure in the refrigeration cycle 

could become abnormally high, causing the pipes to burst.

■ 

)DVWHQDÀDUHQXWZLWKDWRUTXHZUHQFKDVVSHFL¿HGLQWKLVPDQXDO

 ,IIDVWHQHGWRRWLJKWDÀDUHQXWFRXOGEUHDNDQGFDXVHUHIULJHUDQWOHDNDJH

■ 

Install the unit  according to national wiring regulations.

■ 

When opening or closing the valve below freezing temperatures, refrigerant may 

spurt out from the gap between the valve stem and the valve body, resulting in 

injuries.

 Please follow applicable federal, state, or local codes to prevent potential 

leakage/electric shock. Or install a ground fault interrupt for the prevention of 

leakage and electric shock.

  Perform the drainage/piping work securely according to the installation manual.

  If there is defect in the drainage/piping work, water could drip from the unit, and 

damage household items.

 'RQRWWRXFKWKHDLULQOHWRUWKHDOXPLQXP¿QVRIWKHRXWGRRUXQLW

  This could cause injury. 

  Do not install the outdoor unit where small animals may live.

  If small animals enter the unit and damage its electrical parts, it could cause a 

PDOIXQFWLRQVPRNHHPLVVLRQRU¿UH.HHSWKHDUHDDURXQGWKHXQLWFOHDQ

 

CAUTION

(Could lead to serious injury when operated incorrectly.)

 

WARNING

(Could lead to death or serious injury.)

1.  BEFORE INSTALLATION

SPLIT-TYPE AIR CONDITIONERS

INSTALLATION MANUAL

Summary of Contents for MSY-GS36NA









Reviews: