Mitsubishi Electric MR-J5 Series User Manual Download Page 12

Page: 12 / 316

1 INTRODUCTION
1.2 Wiring check

1.2

Wiring check

Power supply system wiring

Before switching on the main circuit and control circuit power supplies, check the following items.

Power supply system wiring

• The power supplied to the power input terminals (L1/L2/L3/L11/L21) of the servo amplifier should satisfy the defined

specifications.



MR-J5-G/MR-J5W-G User's Manual (Introduction)



MR-J5-A User's Manual (Introduction)

• If the power factor improving DC reactor is not used, between P3 and P4 should be connected.

Servo amplifier

Summary of Contents for MR-J5 Series





























































































































































































































































































































Search results

Summary of Contents for MR-J5 Series

Reviews:

Related manuals for MR-J5 Series

Brands by name

Popular brands

Mitsubishi Electric MR-J5 Series, User Manual

Search results

Summary of Contents for MR-J5 Series

Reviews:

Related manuals for MR-J5 Series

Brands by name

Popular brands