manualshive.com logo in svg

Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series, User Manual

Share
Download
Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series User Manual Download Page 133

8  USING A LINEAR SERVO MOTOR

8.6  Absolute position detection system

131

8

8.6

Absolute position detection system

When the linear servo motor is used with the absolute position detection system, an absolute position linear encoder is 
required.

Operating conditions of absolute position detection system

 • Use an absolute position type linear encoder.
 • Perform magnetic pole detection in the incremental system, and disable magnetic pole detection after detection.
 • Enable the absolute position detection system with [Pr. PA03 Absolute position detection system].

Alarm detection

[AL. 025 Absolute position erased], [AL. 092 Battery cable disconnection warning], [AL. 09F Battery warning], and [AL. 0E3 
Absolute position counter warning] are not detected.

Backup

The linear encoder backs up the absolute position data. Therefore, the encoder battery need not be installed to the servo 
amplifier.

Summary of Contents for Melservo-Jet MR-JET G-N1 Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands