Mitsubishi Electric MELSEC iQ-RD77GF16 User Manual Download Page 18

Page: 18 / 116

PERIPHERALS

The following figure shows the peripherals when the RD77MS is used.

• The external input signal cannot be used depending on the connected device. Confirm the specification of

the connected device.

• When using RD77MS2, the external input signals that can be assigned are for 10 points.

RD77MS4

ERR

RUN

SSCNET

cable

External input
signal cable

Synchronous encoder via servo amplifier:
Q171ENC-W8 (Up to 4 modules via
MR-J4-B-RJ), etc.

RD77MS

• Upper stroke limit
• Lower stroke limit
• Proximity dog

External input signals of servo amplifier

Manual pulse generator/
Incremental synchronous encoder

Assigning the external input signals
for 20 points to any of the following
signals.

•

External command signal/Switching

signal

•

Upper stroke limit

•

Lower stroke limit

• Proximity dog

signal

•

Stop signal

Forced stop input (24 V DC)

Servo
motor

MR-J4(W)-B servo amplifier
MR-J3(W)-B servo amplifier
MR-JE-B(F) servo amplifier
Optical hub unit MR-MV200
Inverter FR-A700 series/FR-A800 series
Stepping motor driver AlphaStep/5-phase
manufactured by ORIENTAL MOTOR Co., Ltd.
Servo driver VC

series/VPH series

manufactured by CKD NIKKI DENSO CO., LTD.

IAI electric actuator controller
manufactured by IAI Corporation

RD77MS2: Up to 2 axes
RD77MS4: Up to 4 axes
RD77MS8: Up to 8 axes
RD77MS16: Up to 16 axes

Summary of Contents for MELSEC iQ-RD77GF16





















































































































Search results

Summary of Contents for MELSEC iQ-RD77GF16

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-RD77GF16, User Manual

Search results

Summary of Contents for MELSEC iQ-RD77GF16

Reviews:

Brands by name

Popular brands