Mitsubishi Electric MELSEC FX2N-32DP-IF Hardware Manual Download Page 11 | Manualshive

Page: 11 / 54

background image

Introduction 1

1-1

1.

Introduction

The FX

2N

-32DP-IF(-D) Profibus-DP Interface Unit (called “32DP-IF” hereinafter) can be used

to connect FX

2N

/FX

0N

series extension units/blocks and special function units/blocks directly to

an existing Profibus-DP network.
The 32DP-IF provides an intelligent slave function for decentralized control applications. Digital
and analog data from a Profibus-DP master CPU (called “DP-master” hereinafter) can be sent
and received to/from any of the supported I/O blocks and special function blocks.

1.1

Features of the 32DP-IF

Using the 32DP-IF the FX

2N

/FX

0N

series extension units/blocks and special function units/

blocks can exchange data with any DP-master.

•

Up to 256 I/O points and/or up to 8 special function blocks can be connected to the 32DP-IF.
However, adjust total control I/O points to 256 or less. See section 1.3.

•

The slave address of the 32DP-IF is adjusted by DIP switches. See chapter 4.

•

The 32DP-IF can be connected to a Profibus-DP network via a standard 9-pin D-SUB connector
and a shielded twisted pair cable complying with EN50170. Optional glassfiber adapters are
supported by the 32DP-IF and are available from other vendors.
See chapter 2.

•

An FX-20P-E or personal computer can be used to monitor the status of the 32DP-IF and the
data exchanged with the Profibus network. For operating instructions of the FX-20P-E or
personal computer, refer to their respective operation manuals. For device numbers and
explanation, refer to the FX

2N

-32DP-IF User’s Manual.

FX2N-32DP-IF Profibus-DP Interface Unit

«
...
9
10
11
12
13
...
»

Summary of Contents for MELSEC FX2N-32DP-IF























































Reviews:

No comments

Related manuals for MELSEC FX2N-32DP-IF

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 2

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Brand: Lawler Pages: 5

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: Van Air Pages: 4

Brand: jbc Pages: 44

Brand: jbc Pages: 8

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 2

Brand: Zamel Pages: 2

Brand: Ban Seok Pages: 9

Brand: Elotech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands