1
Checklist of error codes displayed on the PZ-41SLB and LED displays (Table 2-1)
LC 6608
Error code
—
LED1
(green)
—
LED 2
(red)
Lossnay
communi-
cation
error
«
When using multiple Lossnay units, the
main/sub setting has not been made
for the second unit and following units.
«
Multiple transmission cables have
been wired using multi core wires.
«
Transmission cable and power cable
are too close.
«
Transmission cable is not securely
connected.
«
The length of wiring of the transmis-
sion cable is longer than specifica-
tion (longer than 1640 ft).
«
Turn off the main power supply and set
the Main/Sub switch (SW1) (first unit to
main, second and following units to sub).
«
Wire the transmission cable away
from the other transmission cable.
«
Wire the transmission cable at least 5
cm away from the power supply cable.
«
Check the transmission cable con-
nection.
«
Check the length of the transmission
cable wiring.
RC6608
SRC 6608
—
—
Communica
tion error
between
remote con-
trollers
(when 2
remote con-
trollers are
connected)
«
Multiple transmission cables have
been wired using multi core wires.
«
Transmission cable and power sup-
ply cable are too close.
«
Transmission cable is not securely
connected.
«
The length of wiring of the transmis-
sion cable is longer than specifica-
tion (longer than 1640 ft).
«
Wire the transmission cable away
from the other transmission cable.
«
Wire the transmission cable at least 5
cm away from the power supply cable.
«
Check the transmission cable con-
nection.
«
Check the length of the transmission
cable wiring.
LC 0900
SLC 0900
—
—
Lossnay
trial opera-
tion
«
Trial operation switch on the
Lossnay circuit board (SW 2-1 or
SW 2-3) is set to ON board.
«
Check the test operation switch.
LC 4000
SLC 4000
2
blinks
—
Fan motor
operation
device error
«
Lossnay fan will not stop.
«
Replace the table.
LC 3602
SLC 3602
3
blinks
—
Damper
related
error
«
Damper board operation is not cor-
rect.
«
Connectors for the damper unit are
not correctly connected.
«
Remove the load and check or
move the damper board by hand.
«
Check the connection of the lead wire’s
connectors and the circuit connector.
LC 5101
SLC 5101
4
blinks
—
OA thermis-
tor related
error
«
Connectors for the thermistor are
not correctly connected.
«
Check the connection of the lead
wires connectors and the circuit
connector.
LC 5102
SLC 5102
5
blinks
—
RA thermis-
tor related
error
«
Connectors for the thermistor are
not correctly connected.
«
Check the connection of the lead
wires connectors and the circuit
connector.
———
9
blinks
—
Remote
controller
communi-
cation
error
«
Multiple transmission cables have
been wired using multi core wires.
«
Transmission cable and power sup-
ply cable are too close.
«
Transmission cable is not securely
connected.
«
The length of wiring of the transmis-
sion cable is longer than specifica-
tion (longer than 1640 ft).
«
Wire the transmission cable away
from the other transmission cable.
«
Wire the transmission cable at least 5
cm away from the power supply cable.
«
Check the transmission cable con-
nection.
«
Check the length of the transmission
cable wiring.
“Filter” blink-
ing
—
—
Warning to clean air
filter by comulative
operation time
«
Interval for cleaning Lossnay air fil-
ter has elapsed.
«
After cleaning the air filter press the
“Filter” button on the remote con-
troller 2 times.
“HO” blinking blink-
ing
—
System is
starting
«
LED1 blinks at 1 second intervals during
starting operation (maximum of 45 seconds.)
«
There is no error.
Symptom
Cause
Corrective action
*1 LC: Lossnay set to Main SLC: Lossnay set to Sub RC, SRC: remote controller (PZ-41SLB-E)
*2 Because the LGH-F1200RX type is loaded with 2 control circuit units, “SLC” may display even with only 1 Lossnay.
When “SLC” displays, check and perform maintenance on the upper side circuit.
—15—
