«
Check remote control unit number
limitations when using a power
supply unit
«
Check the length of the trans-
mission cable wiring.
«
Check the Lossnay address, and
set for an address corresponding
to interlocked operation.
«
Check the length of the trans-
mission cable wiring.
«
Change to the PZ-52SF-E remote
controller (PZ-41SLB-E can not
be used with the M-NET).
2
System checklist when using the M-NET (Table 1-2-2)
1
No.
Does not interlock with
City Multi. (The Lossnay
cannot be operated by
the ventilation switch on
the ME remote controller,
MA remote controller, or
MELANS.)
«
The Lossnay is not set for interlocked opera-
tion, or is set for interlocked operation at the
wrong address.
«
The length of the M-NET transmission cable
wiring from the outdoor unit or the system’s
overall wiring length is longer than specifica-
tions. (Longer than 656 ft from the outdoor unit,
longer than 1640 ft between ends.)
«
PZ-41LSB-E is connected to the Lossnay local
remote controller.
2
Cannot operate using the
MELANS or Lossnay
remote controller.
«
The address that has been set for the group in
MELANS and the address for the Lossnay are
different.
«
The length of the M-NET transmission cable
wiring from the power supply unit or the sys-
tem’s overall wiring length is longer than speci-
fications. (Longer than 656 ft from the power
supply unit, longer than 1640 ft between ends.)
«
PZ-41LSB-E is connected to the Lossnay local
remote controller.
«
Check the registered address in
MELANS.
«
Check the length of the trans-
mission cable wiring.
«
Change to the PZ-52SF-E remote
controller (PZ-41SLB-E can not be
used with a M-NET system).
3
A unit should operate
independently by
MELANS or the Lossnay
remote controller, but it
interlocks with another
City Multi unit.
«
It has been set for interlocked operation with
the City Multi unit.
«
Cancel the interlocked operation
setting.
4
Cannot perform group
settings for the Lossnay
using MELANS, ME
remote controller, or MA
remote controller. (The
remote controller shows
“88” at the time of regis-
tration.)
«
Power is not supplied to the Lossnay, or power
outside specifications is connected.
«
The M-NET transmission cable is connected to
TM2
5
,
6
.
«
The transmission cable is not properly con-
nected to the MELANS or the City Multi.
«
The length of the transmission cable wiring is longer than
specifications (longer than maximum 656 ft from the
power supply unit, longer than 1640 ft between ends.)
«
Check the power for the Lossnay
and perform the registration again.
«
Connect the transmission cable
to TB5
A
,
B
.
«
Check the transmission cable
connection.
«
Check the length of the trans-
mission cable wiring.
5
When power is supplied
to the system, the
Lossnay remote con-
troller continues to dis-
play “HO” and does not
start. (Group registration
information disappears.)
«
The Group setting was made on a Lossnay
remote controller in a system connected to a
centralised controller MELANS.
«
The length of the transmission cable wiring is
longer than specifications (longer than maxi-
mum 656 ft from the power supply unit, longer
than 1640 ft between ends.)
«
In a system connected to MELANS,
make the group setting with the
MELANS (Do not make the group set-
ting with the Lossnay remote controller).
«
Check the length of the trans-
mission cable wiring.
6
When power is supplied
to the system, the remote
control display goes
blank and the system
does not start.
«
Over the number of units that can be controlled
with the Lossnay remote controller.
«
The length of the transmission cable wiring is
longer than specifications (longer than maxi-
mum 656 ft from the power supply unit, longer
than 1640 ft between ends.)
Symptom
Cause
Corrective action
—13—
