This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to:
(1) Damages caused by any cause found not to be the responsibility of Mitsubishi.
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products.
(3) Special damages and secondary damages whether foreseeable or not, compensation for
accidents, and compensation for damages to products other than Mitsubishi products.
(4) Replacement by the user, maintenance of on-site equipment, start-up test run
and other tasks.
For safe use
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
•
•
•
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Side
A
Side
B
JAPANESE
ENGLISH
JY997D40901D
Side
B
Safety Precautions
(Read these precautions before use.)
This manual classifies the safety precautions into two categories:
and
.
Depending on the circumstances, procedures indicated by
may also
cause severe injury.
It is important to follow all precautions for personal safety.
Associated Manuals
How to obtain manuals
For product manuals or documents, consult with the Mitsubishi Electric dealer
from who you purchased your product.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury or
physical damage.
Manual name
Manual No.
Description
FX
3U
Series
User’s Manual
- Hardware Edition
JY997D16501
MODEL CODE:
09R516
Explains the FX
3U
Series PLC
specification details for I/O, wiring,
installation, and maintenance.
FX
3UC
Series
User’s Manual
- Hardware Edition
JY997D28701
MODEL CODE:
09R519
Explains the FX
3UC
Series PLC
specification details for I/O, wiring,
installation, and maintenance.
FX
3S
/FX
3G
/FX
3GC
/
FX
3U
/FX
3UC
Series
Programming
Manual
- B a s i c & A p p l i e d
Instruction Edition
JY997D16601
MODEL CODE:
09R517
Describes PLC programming for
basic/applied instructions and
devices.
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive and LVD directive for the entire mechanical module
should be checked by the user/manufacturer. For more information please consult with
your nearest Mitsubishi product provider.
Regarding the standards that comply with the main unit, please refer to either the FX
series product catalog or consult with your nearest Mitsubishi product provider.
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (of the identified
standards below) and design analysis (through the creation of a technical construction
file) to the European Directive for Electromagnetic Compatibility (2014/30/EU) when
used as directed by the appropriate documentation.
Attention
This product is designed for use in industrial applications.
Type:
Programmable Controller (Open Type Equipment)
Models:
MELSEC FX
3U
series manufactured
from August 1st, 2010 FX
3U
-8AV-BD
1. Introduction
The FX
3U
-8AV-BD is an expansion board equipped with eight analog set points which
can be used as an analog timer.
1.1 Incorporated Items
Check to ensure the following product and items are included in the package
Standard
Remark
EN61131-2:2007
Programmable controllers
- Equipment requirements
and tests
Com pliance w it h all relevant asp ects of t he
standard.
EMI
• Radiated Emission
• Conducted Emission
EMS
• Radiated electromagnetic field
• Fast transient burst
• Electrostatic discharge
• High-energy surge
• Voltage drops and interruptions
• Conducted RF
• Power frequency magnetic field
Included Item
FX
3U
-8AV-BD
1 unit
Trimmer layout label
1 sheet
M3 tapping screws for installation
2 pcs
Manuals (Japanese version, English version)
1 manual each
1.2 External Dimensions and Part Names
1.3 Trimmer Layout
2. Installation
[1] Mounting holes(2-
φ
3.2 (0.13"))
[2] Special adapter connector cover
[3] Analog volume
[4] Main unit connector
[5] Special adapter connector
INSTALLATION
PRECAUTIONS
•
Make sure to shut down all phases of the power supply externally before
installing.
Failure to do so may cause electric shock or damage to the product.
INSTALLATION
PRECAUTIONS
•
Use the product within the generic environment specifications described in
PLC main unit manual (Hardware Edition).
Never use the product in areas with excessive dust, oily smoke, conductive
dusts, corrosive gas (salt air, Cl
2
, H
2
S, SO
2
or NO
2
), flammable gas,
vibration or impacts, or expose it to high temperature, condensation, or rain
and wind.
If the product is used in such conditions, electric shock, fire, malfunctions,
deterioration or damage may occur.
•
Use screwdrivers carefully when performing installation work, thus avoiding
accident or product damage.
•
When drilling screw holes or wiring, make sure that cutting and wiring debris
do not enter the ventilation slits of the PLC.
Failure to do so may cause fire, equipment failures or malfunctions.
•
Do not touch the conductive parts of the product directly.
Doing so may cause device failures or malfunctions.
•
Connect the extension board securely to their designated connectors.
Loose connections may cause malfunctions.
55.9(2.20")
53.5(2.11")
19.7
(0.78")
46.1(1.82")
[1]
[2]
[5]
[4]
Unit: mm(inches)
MASS(Weight): Approx. 20g(0.05lbs)
Special adapter connector
cover is removed
[3]
VR0 VR1
VR2 VR3
VR4 VR5
VR6 VR7
2.1 Installation Method
The following section describes the installation method to the FX
3U
/FX
3UC
-32MT-
LT(-2) Series PLC.
2.1.1
FX
3U
Series PLC
1) Power off the PLC.
Disconnect all the cables connected to the PLC.
Demount the PLC from the DIN rail.
2) Using a flat head screwdriver as shown in
the figure on the right, lift the dummy
expansion board cover (fig. A) making sure
n o t t o d a m a g e t h e c i rc u i t b o a r d o r
electronic parts.
3) Remove the dummy expansion board
cover (fig. A) perpendicularly away from
the main unit.
4) Make sure the expansion board (fig. B) is in
parallel with the main unit (fig. C) and
attach it to the expansion board connector.
5) Fix the expansion board (fig. B) to the main
unit (fig. C) using the provided M3 tapping
screws (fig. D).
Tightening torque: 0.3 to 0.6 N•m
2.1.2
FX
3UC
-32MT-LT(-2) Series PLC
1) Power off the PLC.
Disconnect all the cables connected to the PLC.
Demount the PLC from the DIN rail.
2) Using a flat head screwdriver as shown in
the figure on the right, lift the dummy
expansion board cover (fig. A) making sure
not to damage the circuit board or electronic
parts.
3) Remove the dummy expansion board cover
(fig. A) perpendicularly away from the main
unit.
4) Make sure the expansion board (fig. B) is in
parallel with the main unit (fig. C) and attach
it to the expansion board connector.
5) Fix the expansion board (fig. B) to the main
unit (fig. C) using the provided M3 tapping
screws (fig. D).
Tightening torque: 0.3 to 0.6 N•m
STOP
FX
3U-48MR/ES
-48MR/ES
FX
3U
3U
-48M
-48M
RUN
0
IN
10
11
OUT
FX
3U
-48M
10
11
12
0
3
1
2
2)
A
3)
RU
N
STOP
FX
3U
3U-48MR/ES
-48MR/ES
FX
FX
3U
-48M
IN
10
1
OUT
FX
3U
-48M
10
1
0
1
2
4)
D
B
5)
D
C
3)
A
2)
5)
D
B
C
4)
3. Specification
3.1 Applicable PLC
3.2 General Specifications
Items other than the following are equivalent to those of the PLC main unit.
For general specifications, refer to the manual of the PLC main unit.
→
Refer to the FX
3U
Series User's Manual - Hardware Edition.
→
Refer to the FX
3UC
Series User's Manual - Hardware Edition.
3.3 Power Supply Specification
3.4 Performance Specification
STARTUP AND
MAINTENANCE
PRECAUTIONS
•
Do not disassemble or modify the PLC.
Doing so may cause fire, equipment failures, or malfunctions.
* For repair, contact your local Mitsubishi Electric representative.
•
Do not drop the product or exert strong impact to it.
Doing so may cause damage.
DISPOSAL
PRECAUTIONS
•
Please contact a certified electronic waste disposal company for the
environmentally safe recycling and disposal of your device.
TRANSPORTATION AND
STORAGE PRECAUTIONS
•
The product is a precision instrument. During transportation, avoid impacts
larger than those specified in the general specifications by using dedicated
packaging boxes and shock-absorbing palettes. Failure to do so may cause
failures in the product. After transportation, verify operation of the product
and check for damage of the mounting part, etc.
Model name
Applicability
FX
3U
Series PLC
Ver. 2.70 and later
FX
3UC
-32MT-LT(-2) PLC
Ver. 2.70 and later
Item
Specification
5V DC power supply (mA)
20mA
(5V DC power is supplied internally from the main
unit.)
Item
Specification
Analog volume points
8 points
Instruction
VRRD(FNC 85) Volume Read
VRSC(FNC 86) Volume Scale
Digital conversion value
VRRD instruction: 0 to 255
VRSC instruction: 0 to 10
4. Program Example
For details on the VRRD and VRSC instruction, refer to the following manuals.
→
Refer to the FX
3S
/FX
3G
/FX
3GC
/FX
3U
/FX
3UC
Series Programming Manual.
1) Example in which the read analog value is used as the set value of an analog
timer. (VRRD instruction)
The analog value of the variable analog potentiometer No.0 is converted into
binary 8-bit data, and the value in the range from 0 to 255 is transferred to D0.
The value of D0 is used as the set value of a timer
When a value larger than 255 is required as the set value of a timer, the read
value multiplied by a constant by the FNC22 (MUL) instruction can be set
indirectly as the timer constant.
2) Example in which the scale value is used as a rotary switch. (VRSC instruction)
Either one among auxiliary relays M0 to M10 turns ON in accordance with the
scale value in the range from 0 to 10 of the specified variable analog
potentiometer.
5. Trimmer Layout Label
The trimmer layout label is adhere it in a position where it can be seen easily for quick
reference (as shown in the figure below).
•
In the case of FX
3U
Series PLC
•
In the case of FX
3UC
-32MT-LT(-2) PLC
K0
D0
X000
X001
T0
D0
Volume
number
Read
destination
FNC 85
VRRD
X000
X001
M0
M1
M10
M0 turns ON when the scale value is "0".
M1 turns ON when the scale value is "1".
M10 turns ON when the scale value is "10".
K1
D1
FNC 86
VRSC
D1
M0
K4
FNC 41
DECO
The FNC41 (DECO)
instruction occupies
auxiliary relays
M0 to M15.
VR
0
VR
1
VR
2
VR
3
VR
4
VR
5
VR
6
VR
7
VR
0
VR
1
VR
2
VR
3
VR
4
VR
5
VR
6
VR
7
6. Caution On Use
•
Only one analog volume expansion board can be used per main unit.
•
The communication function is not available at ch1 when VRRD or VRSC
instruction is used in the program in FX
3U
/FX
3UC
PLCs.
含有有害6物质的名称，含有量，含有部品
本产品中所含有的有害6 物质的名称，含有量，含有部品如下表所示。
产品中有害物质的名称及含量
本表格依据SJ/T 11364的规定编制。
○:表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
规定的限量要求以下。
×:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T
26572规定的限量要求。
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴
二苯醚
(PBDE)
可编程
控制器
外壳
印刷基板
○
○
○
○
○
○
○
○
○
○
○
×
「电器电子产品有害物质限制使用标识要求」的表示方式
Note: This symbol mark is for China only.
基于中国标准法的参考规格:GB/T15969.2
FX
3U
-8AV-BD
USER'S MANUAL
This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and the manuals of all relevant
products fully to acquire proficiency in handling and operating the product. Make
sure to learn all the product information, safety information, and precautions.
Store this manual in a safe place so that it can be taken out and read whenever
necessary. Always forward it to the end user.
Registration:
The company and product name described in this manual are registered
trademarks or the trademarks of their respective companies.
Effective June 2018
Specifications are subject to change without notice.
©
2010 Mitsubishi Electric Corporation
Manual Number
JY997D40901
Revision
D
Date
June 2018
