Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 285

Page: 285 / 356

280

Setting the parameter unit and operation panel

(3) Disable the setting dial and key operation of the operation panel (Press [MODE] long (2s))



Operation using the setting dial and key of the operation panel can be invalid to prevent parameter change, and

unexpected start or frequency setting.



Set "10 or 11" in

Pr. 161

, then press

for 2s to make the setting dial and key operation invalid.



When the setting dial and key operation are invalid,

appears on the operation panel. If dial or key operation is

attempted while dial and key operation are invalid,

appears. (When dial or key is not touched for 2s, monitor

display appears.)



To make the setting dial and key operation valid again, press

for 2s.

REMARKS



Even if the setting dial and key operation are disabled, the monitor display and

are valid.

NOTE



Release the operation lock to release the PU stop by key operation.

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Brands by name

Popular brands

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Search results

Summary of Contents for FR-F700PJ Series

Reviews:

Brands by name

Popular brands