manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Share
Download
Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 278

273

Useful functions

4

P

ARAM

ETE

R

S

4.22.7 Setting multiple parameters as a batch (Pr.999)

(1)

Automatic parameter setting (Pr.999)

Select which parameters to be automatically set, and set that to 

Pr. 999

. Multiple parameter settings are changed

automatically. 

Refer to page 276

 for the list of parameters that are changed automatically. 

Parameter settings are changed as a batch. Those include communication parameter settings for the Mitsubishi
human machine interface (GOT) connection and rated frequency settings of 50Hz/60Hz.

Multiple parameters are changed automatically. Users do not have to consider each parameter number. (Parameter
setting mode)

Parameter 

Number

Name

Initial value

Setting range

Description

999

Automatic parameter setting

9999

10

GOT initial setting (PU connector)

20

50Hz rated frequency

21

60Hz rated frequency

9999

No action

The read value is always 

"

9999

"

.

Pr.999 setting

Description

Operation in the parameter setting 

mode

10

Automatically sets the communication parameters for the GOT 
connection with a PU connector

(AUTO) 



(GOT) 



Write "1"

20

50Hz rated 
frequency

Sets the related parameters of the rated 
frequency according to the power supply 
frequency

(AUTO) 



(F50)  



Write "1"

21

60Hz rated 
frequency

—

REMARKS

If the automatic setting is performed, the selected settings including the changed parameter settings will be changed. 

Setting 

Pr. 999

 = "20 or 21" during the machine speed display changes the 

Pr. 505 Speed setting reference

 setting to 60Hz or to

50Hz. After setting 

Pr. 999

 = "20 or 21", calculate the rotations per minute at the changed 

Pr. 505

 setting, and set 

Pr. 37 Speed

display

 again.

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands