manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

Share
Download
Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 195

190

Frequency setting by analog input (terminal 2, 4)

4.17.5 Frequency setting signal (current) bias/gain adjustment method

(a) Method to adjust any point by application of a voltage (current) across terminals 2 and 5 (4 and 5).

Follow the following procedure to adjust the bias and gain of the frequency setting voltage (current) using the operation
panel. 

Refer to page 188

 for the details of parameters.

Operation Display 

1.

Confirm the operation status indicator and 

operation mode indicator

The inverter should be at a stop.

The inverter should be in the PU operation 
mode.

(Using )

2.

Press 

 to choose the parameter setting 

mode.

PRM indicator is lit.

(The parameter number read previously appears.)

3.

Turn 

 until 

 appears.

4.

Press 

 to display 

.

5.

Turn 

 until 

 (

) appears.

Set to 

C4

 

Terminal 2 frequency setting gain.

Terminal 2 input is 

selected

Terminal 4 input is 

selected

6.

Press 

 to display the analog voltage 

(current) value (%).

Analog voltage (current) 
value (%) across terminals 2 
and 5 (across terminals 4 
and 5)

7.

Apply a 5V (20mA) voltage (current).

(Turn the external potentiometer connected 
across terminals 2 and 5 (across terminals 4 
and 5) to maximum (any position).)

* The value is nearly 100 (%) in the maximum position of

the potentiometer.

8.

Press 

 to set.

Terminal 2 input is 
selected

Terminal 4 input is 
selected

Flicker...Parameter setting complete!!

* The value is nearly 100 (%) in the maximum position of

the potentiometer.

Turn 

 to read another parameter.

Press 

 to return to the 

 indication (step 4).

Press 

 twice to show the next parameter (

).

REMARKS

If the frequency meter (display meter) connected across the terminals FM and SD does not indicate exactly 60Hz, set the

calibration parameter C0 FM terminal calibration

. 

(Refer to page 158)

If the gain and bias of frequency setting voltage (current) are too close, an error ( 

) may be displayed at setting.

C0 to C25 settings 
are enabled.

Hz

A

Hz

A

NOTE

After performing operation in step 6, do not touch 

 

until completion of calibration.

Hz

A

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands