Mitsubishi Electric F720PJ-11KF, Manual

Page: 60 / 96

60
Stand-alone option
Name (model) Specification and Structure
Enclosure surface
operation panel
FR-PA07
 An operation panel that enables inverter operation and monitoring of frequency setting, etc. from the enclosure surface.
 Outline drawing and enclosure cut dimension drawing (Refer to page 16)
(Note) 1. The operation panel cannot be removed from the inverter.
2. The separate parameter unit connection cable (FR-CB20  ) is required.
DIN rail installation
attachment
FR-UDA

 An attachment to install an FR-F700PJ series inverter to a DIN rail.
 Outline dimension drawing
[FR-UDA01] [FR-UDA02] [FR-UDA03]
AC reactor (for power
supply coordination)
FR-HAL-(H)
 K
 Improves the power factor and reduces the harmonic current at the input side. Connect an AC reactor at the input side of the inverter.
 Selection method
Select an AC reactor according to the applied motor capacity.
(When a general-purpose motor is used, select it according to the motor capacity even if the capacity is smaller than the inverter capacity.)
 Connection diagram
 Outline dimension
 Specification
Item Description
Surrounding air
temperature
-10°C to +50°C (non-freezing)
Ambient humidity 90%RH or less (non-condensing)
Storage
temperature
-20°C to +60°C
Atmosphere Indoors (free from corrosive gas, flammable gas, oil mist, dust and dirt)
Maximum altitude/
Vibration
1,000m or less, 5.9m/s
2
or less
Power supply Power input from the inverter
Connection method Connection using the parameter unit connection cable (FR-CB20

)
 Selection table
Installation attachment
model
Inverter capacity
FR-F720PJ FR-F740PJ
FR-UDA01 0.4K, 0.75K

FR-UDA02 1.5K, 2.2K 0.4K to 3.7K
FR-UDA03 3.7K

108
67
68
67
128 128
4-M4 0.7 screw
8.7
3-M4 0.7 screw
Hook
Hook
15
15
10
8.7
8.7
128
67
170
4-M4 0.7 screw
Hook
14.4
(Unit: mm)
M
R/L1
S/L2
T/L3
U
V
W
R
S
T
X
Y
Z
Three-phase AC
power supply
Inverter FR-HAL
Motor
(Unit mm)
(Note) 1. Approximately 88% of the power factor improving effect can be obtained (92.3% when calculated with 1
power factor for the fundamental wave according to the Architectural Standard Specifications (Electrical Installation) (2013 revision)
supervised by the Ministry of Land, Infrastructure, Transport and Tourism of Japan).
2. This is a sample outline dimension drawing. The shape differs by the model. W1 and D1 indicate distances between installation holes. The
installation hole size is indicated by d.
3. Install AC reactors (FR-HAL) on a horizontal or vertical surface.
4. Keep enough clearance around the reactor because it heats up. (Keep a clearance of minimum 10cm each on top and bottom and minimum
5cm each on right and left regardless of the installation orientation.)
Model W W1 H D D1 d
Mass
(kg)
Model W W1 H D D1 d
Mass
(kg)
20
0V
0.4K
104 84 99 72 40 M5 0.6
40
0V
H0.4K
135 120 115 64 45 M4 1.5
0.75K
104 84 99 74 44 M5 0.8
H0.75K
135 120 115 64 45 M4 1.5
1.5K
104 84 99 77 50 M5 1.1
H1.5K
135 120 115 64 45 M4 1.5
2.2K
115 40 115 77 57 M6 1.5
H2.2K
135 120 115 64 45 M4 1.5
3.7K
115 40 115 83 67 M6 2.2
H3.7K
135 120 115 74 57 M4 2.5
5.5K
115 40 115 83 67 M6 2.3
H5.5K
160 145 142 76 55 M4 3.5
7.5K
130 50 135 100 86 M6 4.2
H7.5K
160 145 142 96 75 M4 5.0
11K
160 75 164 111 92 M6 5.2
H11K
160 145 146 96 75 M4 6.0
15K
160 75 167 126 107 M6 7.0
H15K
220 200 195 105 70 M5 9.0
Less than D
D1
W
W1
H