Mitsubishi Electric E1071 Installation Manual Download Page 11

Technical Data

Mitsubishi Electric, MA00777A

3-1

3

Technical Data

Parameter

E1071

Front panel, W x H x D 219 x 154 x 6 mm 
Mounting depth

55 mm (155 mm including clearance) 

Front panel seal

IP 66

Rear panel seal

IP 20

Keyboard material/
Front panel

Touch screen: Polyester on glass *, 1 million finger touch 
operations. 
Overlay: Autotex F250 *.

Reverse side material

Powder-coated aluminum

Weight

1.1 kg 

Serial port RS422/
RS485

25-pin D-sub contact, chassis-mounted female with 
standard locking screws 4-40 UNC.

Serial port RS232C

9-pin D-sub contact, male with standard locking screws 4-40 
UNC.

Ethernet

Shielded RJ 45

USB

Host type A (USB 1.1), max output current 500mA
Device type B (USB 1.1)

CF-slot

Compact flash, type I and II

Flash memory for 
application

12 MB (incl. fonts)

Real time clock

±20 PPM + error because of ambient temperature and supply 
voltage. 
Total max error: 1 min/month at 25 

°

C

Minimum life of the real time clock battery: 3 years
Temperature coefficient: 0.004 ppm/

°

C

2

Power consumption at 
rated voltage

Normal: 0.4 A 
Maximum: 0.9 A

Display

TFT-LCD. 640 x 480 pixels, 64K color. 
CCFL backlight lifetime at the ambient temperature of 
+25 

°

C: >50,000 h.

Active area of display, 
W x H

131.5 x 98.6 mm 

Fuse

Internal DC fuse, 3.15 AT, 5 x 20 mm

Power supply

+24V DC (20 - 30V DC). 3-pin jack connection block.
CE: The power supply must conform with the requirements 
for SELV or PELV according to IEC 950 or IEC 742.
UL: The power supply must conform with the requirements 
for class II power supplies.

Ambient temperature

Vertical installation: 0 

° 

to +50 

°

C

Horizontal installation: 0 

° 

to +40 

°

C

Storage temperature

-20 

°

 to +70 

°

C

Relative humidity

5 - 85 % non-condensed

EMC tests on the 
operator terminal

The operator terminal conforms with the essential protection 
requirements in article 4 of the directive 89/336/EEC. Noise 
tested according to EN610

0

0-6-4 emission and EN61000-6-2 

immunity. 

UL, cUL approvals 
(when procuct or 
packing is marked)

UL 1604 Class I, Div 2 / UL 508 / UL 50 4x indoor use only

DNV

Yes

NEMA

4x indoor use only

* See section 

Chemical Resistance

Summary of Contents for E1071





















Reviews: