Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 90 | Manualshive

Page: 90 / 162

background image

88

7 FUNCTIONS
7.6 CC-Link IE Field Network Communication Function

■

Data storage configuration

Configure the data storage setting for each channel.
The data storage is the area in which the IO-Link device parameters are stored, and is used by the IO-Link device setting
automatic upload/download function.

The following table shows the data storage configuration and data configuration of each channel.

• Upload setting

• Download setting

• Data storage deletion request

• Data storage configuration

Enable the Data storage configuration when the Upload setting and Download setting are enabled. It is not
possible to enable only the Data storage configuration.
Disable the Data storage configuration when the Data storage deletion request is enabled.

Item

Description

Access code

22H

Attribute code

05H

Address code

00H

Data size

8 bytes

Data

• First byte: The data storage configuration of the IO-Link module channel 1 (Default: 00H)
• Second byte: The data storage configuration of the IO-Link module channel 2 (Default: 00H)
• Third byte: The data storage configuration of the IO-Link module channel 3 (Default: 00H)
• Fourth byte: The data storage configuration of the IO-Link module channel 4 (Default: 00H)
• Fifth byte: The data storage configuration of the IO-Link module channel 5 (Default: 00H)
• Sixth byte: The data storage configuration of the IO-Link module channel 6 (Default: 00H)
• Seventh byte: The data storage configuration of the IO-Link module channel 7 (Default: 00H)
• Eighth byte: The data storage configuration of the IO-Link module channel 8 (Default: 00H)

Data configuration

Description

b0

Upload setting (0: Disabled, 1: Enabled)

b1

Download setting (0: Disabled, 1: Enabled)

b2 to b5

Use prohibited (fixed to 0)

b6

Data storage deletion request (0: Not delete, 1: Delete)

b7

Data storage configuration (0: Disabled, 1: Enabled)

• Enabled: Parameters of each IO-Link device parameters are uploaded to the data storage of the IO-Link module.
• Disabled: Parameters of each IO-Link device are not uploaded. However, if there is no parameters in the data storage of the IO-Link module, the IO-Link

device parameters are uploaded.

• Enabled: Parameters in the data storage of the IO-Link module are downloaded to each IO-Link device.
• Disabled: Parameters in the data storage of the IO-Link module are not downloaded.

• Delete: Parameters saved in the data storage of the IO-Link module are deleted.
• Not delete: Parameters saved in the data storage of the IO-Link module are not deleted.

• Enabled: Parameters are saved in the data storage of the IO-Link module.
• Disabled: Parameters are not saved in the data storage of the IO-Link module. However, if parameters already exist in the data storage, the parameters are

not deleted even if this setting is disabled.

«
...
88
89
90
91
92
...
»

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Reviews:

No comments

Related manuals for CC-Link IE Field NZ2GF12A-60IOLH8

Brand: GBD Pages: 68

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Federal Signal Corporation Pages: 60

Brand: FASTRON. Pages: 16

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Brand: PACH & COMPANY Pages: 4

Brand: Water Specialist Pages: 60

NOVASTAT EL DIGITAL

Brand: Taconova Pages: 7

Brand: National Instruments Pages: 14

Brand: GBD Pages: 60

Brand: IBCcontrol Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands