manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 88

86

8  PROGRAMMING
8.2  Program Example

Parameter setting

Setting in the master station

Connect the engineering tool to the CPU module on the master station and set parameters.

1.

Set the CPU module as follows.

[Project] 

 [New]

2.

In "CPU Parameters", set "Link Direct Device Setting" to "Extended Mode (iQ-R Series Mode)".

[CPU parameters] 

 [Memory/Device Setting] 

 [Link Direct Device Setting] 

 [Link Direct Device Setting]

When using the engineering tool to write the module parameters of RJ71GN11-T2 to the CPU module, set 
"Link Direct Device Setting" to "Extended Mode (iQ-R Series Mode)".
When "Link Direct Device Setting" is "Q Series Compatible Mode", "Write to PLC" cannot be executed.

3.

Set the master/local module as follows.

[Navigation window] 

 [Parameter] 

 [Module Information] 

 right-click 

 [Add New Module]

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands