manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 42

40

6  CONFIGURATION
6.1  Network Configuration Settings

6

CONFIGURATION

6.1

Network Configuration Settings

Before setting the NZ2AW1GNAL parameters, write the network parameters to the CPU module of the master station.
Also when changing the network configuration, change the network parameters and write them to the CPU module.
For details on how to set the master station, refer to the following.

User's manual for the master station used

If the number of remote I/O signal points and remote register points are set to be less than that in the 
NZ2AW1GNAL, no error will occur and the data for the number of points set from the beginning will be 
transmitted by cyclic transmission.

The items of the NZ2AW1GNAL set by the engineering tool are as follows.

Item

Description

Station address

Set the station number of the NZ2AW1GNAL.

Station type

Set "Remote Station".

RX/RY setting (points)

Set "32" + input or output value of "Bit data points setting".

RWw/RWr setting (points)

Set "32"+ input or output value of "Word data points setting".

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands