manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 183

APPX

Appendix 5  Processing Time

181

A

Response delay time

The following shows the response delay time of input and output.

Input response delay time

The figure below shows the time between a signal input to the slave module and the remote device turning on/off.
The input response delay time is the total of 

 to 

 in the following figure.

(1) Input device
(2) AnyWireASLINK system
(3) CC-Link IE TSN

No.

Description

Required time

Input response time on the slave module

Refer to the manual of the slave module connected to the system (manufactured by Anywire 
Corporation).

Transmission time

• Bit data: Bit transmission cycle time 

 2

• Word data: Word transmission cycle time

The transmission cycle time varies depending on the specified number of bit data points and the 
specified number of word data points.

Page 178 Transmission cycle time formula

Processing time of the NZ2AW1GNAL

1.0ms

Ô

Ò

(1)

(2)

(3)

Ó

Input

Output to CC-Link IE TSN side

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands