manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 139

APPX

Appendix 1  Remote I/O Signals

137

A

Details of remote output signals

Error reset request flag

■

Device No.

■

Description

When Error reset request flag (RY0) is turned off and on when a minor error and alarm occurs, the error information and alarm 
information are cleared. However, the error information will not be cleared if Parameter access completion flag (RX11) is off.
The signals that are cleared when the error information and alarm information are cleared are as follows.
 • DP/DN short error (RX1)
 • 24V/DP short error (RX2)
 • DP/DN disconnection error (RX4)
 • Error status flag (RX5)
 • Alarm status flag (RX6)
 • AnyWireASLINK version compatibility inspection error flag (RX8)
 • Slave module alarm signal (RX10)
 • Parameter access error (RX12)
 • Latest error code storage area (RWr0)
 • Latest error ID storage area (RWr1)
 • Latest alarm code storage area (RWr2)
 • Latest alarm ID storage area (RWr3)
 • Number of the IDs of the disconnected modules (RWr6)
 • Number of the alarm IDs (RWr8)
 • Disconnected module ID information storage area (5100H to 51FFH)
 • Disconnected module ID information bit area (5200H to 527FH)
 • Alarm ID information storage area (5500H to 55FFH)
 • Version compatibility inspection error ID area (5700H to 577FH)

Automatic address detection command

■

Device No.

■

Description

When Automatic address detection command (RY1) is turned off and on, the automatic address detection is executed.
For details on automatic address detection, refer to the following.

Page 53 Automatic Address Detection Function

Name

Device No.

Error reset request flag

RY0

Name

Device No.

Automatic address detection command

RY1

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands