manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 136

134

APPX
Appendix 1  Remote I/O Signals

Parameter access completion flag

■

Device No.

■

Description

This flag turns on after Remote READY (RX0) turns on.
It turns off while any of the following is being executed.
 • Slave module parameter read/write
 • AnyWireASLINK version compatibility inspection function
 • Easy replacement function for one slave module
 • Automatic address detection
 • Slave information acquisition at start-up function
 • Remote address change function

Parameter access error

■

Device No.

■

Description

This signal turns on when an error occurs due to noise or other causes during parameter access.

■

Turning off Parameter access error

To turn off Parameter access error (RX12), after eliminating the error, perform either of the following operations.
Until then, Parameter access error (RX12) remains on.
 • Turn off and on the NZ2AW1GNAL or execute the remote reset.
 • Turn on and off Error reset request flag (RY0).

Automatic address detection flag

■

Device No.

■

Description

The signal remains on from the start of execution of automatic address detection to the end of the execution.

Address inspection flag

■

Device No.

■

Description

The signal remains on from the start of execution of address inspection to the end of the execution.

Name

Device No.

Parameter access completion flag

RX11

Name

Device No.

Parameter access error

RX12

Name

Device No.

Automatic address detection flag

RX14

Name

Device No.

Address inspection flag

RX15

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands