manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 133

APPX

Appendix 1  Remote I/O Signals

131

A

Alarm status flag

■

Device No.

■

Description

This signal turns on when an alarm occurs. For details on the alarms, refer to the following.

Page 142 Latest alarm code storage area

Page 143 Latest alarm ID storage area

■

Turning off Alarm status flag

After eliminating the cause of the alarm, Alarm status flag (RX6) remains on until either of the following operations is 
performed.
 • Turning off and on the NZ2AW1GNAL or executing the remote reset
 • Turn on and off Error reset request flag (RY0).

AnyWireASLINK version compatibility inspection error flag

■

Device No.

■

Description

This signal turns on when an error is detected in the AnyWireASLINK version compatibility inspection.

■

Turning off AnyWireASLINK version compatibility inspection error

To turn off AnyWireASLINK version compatibility inspection error flag (RX8), eliminate the cause of the error and perform 
either of the following operations.
Until then, AnyWireASLINK version compatibility inspection error (RX8) remains on.
 • Turn off and on the NZ2AW1GNAL or execute the remote reset.
 • Turn on and off Error reset request flag (RY0).
 • Turn off and on AnyWireASLINK version compatibility inspection command (RYD).

Name

Device No.

Alarm status flag

RX6

Name

Device No.

AnyWireASLINK version compatibility inspection error flag

RX8

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands