manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 132

130

APPX
Appendix 1  Remote I/O Signals

Module power supply voltage drop error

■

Device No.

■

Description

This signal turns on when the module power supply (24V) voltage drops.

■

Turning off Module power supply voltage drop error

To turn off Module power supply voltage drop error (RX3), after eliminating the voltage drop of the module power supply (24V), 
perform the following operations.
Until then, Module power supply voltage drop error (RX3) remains on.
 • Turn off and on the NZ2AW1GNAL or execute the remote reset.

DP/DN disconnection error

■

Device No.

■

Description

This signal turns on when the transmission cables (DP, DN) or a slave module is disconnected.

■

Turning off DP/DN disconnection error

To turn off DP/DN disconnection error (RX4), after eliminating the disconnection in the transmission cables (DP, DN) or that of 
the slave module, perform either of the following operations.
Until then, DP/DN disconnection error (RX4) remains on.
 • Turn off and on the NZ2AW1GNAL or execute the remote reset.
 • Turn on and off Error reset request flag (RY0).

Error status flag

■

Device No.

■

Description

This signal turns on when an error occurs. For details on the errors, refer to the following.

Page 142 Latest error code storage area

Page 142 Latest error ID storage area

■

Turning off Error status flag

The timing at which Error status flag (RX5) turns on and off differs depending on the error classification. For details, refer to 
the following.

Page 120 How to reset errors and alarms

Name

Device No.

Module power supply voltage drop error

RX3

Name

Device No.

DP/DN disconnection error

RX4

Name

Device No.

Error status flag

RX5

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands