manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 109

9  MAINTENANCE AND INSPECTION

9.1  Daily Inspection

107

9

9

MAINTENANCE AND INSPECTION

To maintain the best condition of the system, perform the inspection in accordance with the items described in the user's 
manual of the CPU module used.
This chapter describes the product-specific items that are not described in the user's manual of the CPU module used.

9.1

Daily Inspection

The following table lists the items that must be inspected on a daily basis.

Item

Inspection Item

Inspection method

Judgment criterion

Action

1

Mounting of the 
NZ2AW1GNAL

Looseness of the 
NZ2AW1GNAL

Check that the tabs of the 
NZ2AW1GNAL are securely 
hooked on the DIN rail.

The NZ2AW1GNAL must be 
mounted on the DIN rail 
securely.

Hook the tabs of the 
NZ2AW1GNAL on the DIN rail 
securely.

2

Connection 
status

Terminal screw 
loosening

Check for the terminal screw 
loosening.

The terminal screws must not 
be loose.

Retighten the terminal screws.

Clearance between the 
solderless terminals

Check for the clearance 
between the solderless 
terminals.

The proper clearance must be 
provided between solderless 
terminals.

Provide the proper clearance.

Connector loosening

Check for the cable connector 
loosening.

The cable connector must not 
be loose.

Tighten the terminal block 
mounting screws securely.

3

LED status

PW LED

Check that the LED is on.

The LED must be on.

Refer to the following and take 
actions. (

 Page 109 

Checking with LEDs)

RUN LED

Check that the LED is on.

The LED must be on.

D LINK LED

Check that the LED is on.

The LED must be on.

ERR. LED

Check that the LED is off.

The LED must be off.

LINK LED

Check that the LED is on or 
flashing.

The LED must be on during the 
version compatibility 
inspection. The LED must be 
flashing during a data link.

SET LED

Check that the LED is off.

The LED must be off.

ALM LED

Check that the LED is off.

The LED must be off.

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands