manualshive.com logo in svg

Mitsubishi Electric A800-E, Instruction Manual

Share
Download
Mitsubishi Electric A800-E Instruction Manual Download Page 5

Ethernet cable wiring precautions

4

INTRODUCTION

1.3

Ethernet cable wiring precautions

This section explains Ethernet cable connection and the relevant precautions.

Handling of the Ethernet cable

 • Do not touch the conductors of the cable or the connector on the inverter. Keep the conductors free of dust or dirt. Handling 

the conductors with oily hands or dust/dirt adhesion to the conductors may cause transmission losses and impair normal 
data link operation.

 • Check the Ethernet cable for the following points before use.

 • The cable is not broken.
 • The cable does not have a short circuit.
 • The connector is properly installed.

 • Do not use an Ethernet cable with a broken latch. Doing so may cause the cable to come off or malfunction.
 • Do not connect the Ethernet cable to the PU connector. The product could be damaged due to differences in electrical 

specifications.

 • The maximum distance between stations is specified as 100 m. However, the maximum distance may be shorter 

depending on the environment. For details of the cable, contact your cable manufacturer.

Connecting and disconnecting of the Ethernet cable

Hold the cable connector when connecting and disconnecting the Ethernet cable. Pulling a cable connected to the inverter 
may damage the inverter or cable, or result in malfunction due to poor contact.

Network configuration

Check the network configuration before wiring, and perform correct wiring.

Summary of Contents for A800-E





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands