manualshive.com logo in svg

Mitsubishi Electric A800-E, Instruction Manual

Share
Download
Mitsubishi Electric A800-E Instruction Manual Download Page 19

(N) Operation via communication and its settings

18

PARAMETER

Error reset operation selection at inverter fault (Pr.349)

 • In the External operation mode or the PU operation mode, use this parameter to disable an error reset command sent 

through the Ethernet network (CC-Link IE Field Network Basic) or from a communication option.

Operation mode switching and communication startup mode (Pr.79, 
Pr.340)

 • Check the following before switching the operation mode.

- The inverter is at a stop.
- Both the STF and STR signals are off.
- The 

Pr.79 Operation mode selection

 setting is correct. (Check the setting on the operation panel of the inverter.)

 • The operation mode at power ON and at restoration from instantaneous power failure can be selected. Set a value other 

than "0" in 

Pr.340

 

Communication startup mode selection 

to select the Network operation mode.

 • After the inverter starts up in the Network operation mode, parameter write can be commanded via the network.

NOTE

 • The changed value in 

Pr.340

 is applied after the next power-ON or inverter reset.

  • The 

Pr.340

 setting can be changed on the operation panel in any operation mode.

 • When setting a value other than "0" in 

Pr.340

, make sure that the communication settings of the inverter are correct.

Parameters referred to

Pr.7 Acceleration time, Pr.8 Deceleration time 

Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter

Pr.79 Operation mode selection 

Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter

Pr.340 Communication startup mode selection 

Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter

Pr.550 NET mode operation command source selection 

page 9

Pr.551 PU mode operation command source selection 

page 9

Pr.1431 Ethernet signal loss detection function selection 

page 19

Pr.1432 Ethernet communication check time interval 

page 19

CAUTION

When Pr.502 = "3" and a communication line error occurs, or Pr.502 = "4" and a communication line 
error or a communication option fault occurs, the operation continues. When setting "3 or 4" in 
Pr.502, provide a safety stop countermeasure other than via communication. For example, input a 
signal (RES, MRS, or X92) through an external terminal or press the PU stop on the operation panel.

Pr.349 setting

Description

0 (initial value)

Error reset is enabled independently of operation mode

1

Error reset is enabled only in the network operation mode

Summary of Contents for A800-E





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands