background image

260B Blower / 280BV Blower Vacuum

2

Original Instructions Version July 12

Component Location

 

 

 

 

 

1. Ignition Switch 

ON-OFF toggle switch. Switch to ON before starting. Switch to OFF to stop engine

2. Spark Plug

 

Provides spark to ignite 2-stroke fuel mixture

3. Air Cleaner

 

Replaceable air filter

4. Fuel Tank

 

Contains fuel and fuel filter

5. Fuel Cap 

Seals fuel inside fuel tank

6. Recoil Starter

 

Pull to start engine

7. Muffler

  

Controls exhause emissions and noise

8. Choke 

 

To assist cold starting. Fully extend to close choke.  

Push in to open choke. 

9. Primer Bulb

 

Draws fuel from fuel tank and purges air from the carburetor prior to starting.

10. Blower Pipes

 

Two parts lock together to form air discharge pipe.

11. Throttle Lever

  Pull to increase engine speed.

12. Vacuum Tube

 

Two parts lock together to form air intake pipe. Vacuums in debris to be shredded.

13. Vacuum Elbow

  Discharges shredded materials into collection bag.

14. Collection Bag

  Collects shredded materials with zip to empty.

15. Side Cover

 

Must be closed when in blower mode.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

Summary of Contents for 260B



























Reviews: