Mitel SST2 User Manual Download Page 13 | Manualshive

Page: 13 / 14

Mitel SST2 User Manual Download Page 13

33/1531-ANF 901 43 Uen C 2017-03-28

User Guide
Site Survey Tool for DECT

13

Figure 7. LED on IPBS4x2/IPBS2

Figure 8. LED deployment indications on IPBS4x2/IPBS2

16

Use the GUI web interface on base station B and check the signal strength on
the actual synchronization coverage and name it X.

17

Perform an RFP scan. If there are other DECT systems that are stronger than
(X-6) dBm, move base station B closer to base station A and then repeat from
step 10 above. For example, if X = -80 dBm then there must be no other DECT
systems that are stronger than -86 dBm.

4.4 TO PERFORM MEASUREMENTS FOR OTHER BASE

STATIONS

18

Move base station A to the position where base station B is located.

19

Place base station B on the next planned position.

20

Repeat from step 7 above.

LED

IPBS2

Deployment:
Good sync

mode and has good air sync

The IPBS4x2/IPBS2 is in deploy

coverage.

Deployment:
Bad sync

The IPBS4x2/IPBS2 is in deploy
mode and does not have
adequate air sync coverage.

Deployment:
No sync

mode and has no air sync

The IPBS4x2/IPBS2 is in deploy

coverage.

2000 ms blue, 400 ms yellow.

400 ms blue, 600 ms off, 400 ms blue,
600 ms off, 400 ms yellow.

2000 ms red, 400 ms yellow.

«
...
11
12
13
14
»

Summary of Contents for SST2















Reviews:

No comments